675035
16
Zoom out
Zoom in
Previous page
1/20
Next page
POWX07582 EN
Copyright © 2017 VARO P a g e | 16 www.varo.com
11.2.5 Changing the saw blade (Fig. 5)
HAZARD!The saw blade may be extremely hot and can cause burns,
immediately after you have stopped sawing. Always led a hot saw blade
cool off. Never clean saw blades with flammable liquids.
This can cause injuries, also when the saw blade is not turning. The
movable saw blade guard must cover the saw blade, whenever you tighten
or release the driveshaft bolt (E1).
Always wear gloves while changing the saw blade.
Set the support arm to 0° (vertical) and tighten the bevelling lock nut.
For removing the topmost sawing table, loosen the corresponding screws. Remove the
sawing table.
To prevent that the saw blade rotates, pull the saw blade lock (D1) forward. Use your hand
at the same time to turn the saw blade slowly, until the saw blade latch is activated.
Loosen the driveshaft bolt (E1) of the saw (left-turning thread).
Remove the shaft bolt (E1) and the outer saw flange (E2) from the saw shaft.
Remove the saw blade (18) from the saw shaft and lift it up to remove it from the machine.
Remove the shaft nut (E4) and the inner saw flange (E3) from the saw shaft.
Clean the surfaces of the following components:
The saw shaft
The inner saw flange
The saw blade
The outer saw flange
The shaft nut
The saw blade guard
HAZARD! Do not use any cleaning products (for instance for removing
resin residues) that have the tendency to cause corrosion on light metals;
this could damage the machine.
Fasten the shaft nut (E4) of the inner saw flange (E3) on the saw shaft.
HAZARD! Be sure to fasten the inner saw flange correctly! The saw may
block, or the saw blade may come lose, if the flange is not correctly
fastened. The inner saw flange is correctly mounted when the bevelled
collar (Q1) points to the right and the spring groove points to the left (Fig.
6).
Mount the new saw blade (18) and check the rotating direction (the arrow on the saw
blade must point in the same direction as the arrow on the saw blade guard!).
HAZARD! Only use saw blades that conform to the applicable standards
and that can be used at the maximum speed indicated in the technical data
sheet.
DO NOT use:
Wrong saw blades
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07582 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07582

Powerplus POWX07582 User Manual - German - 22 pages

Powerplus POWX07582 User Manual - Dutch - 22 pages

Powerplus POWX07582 User Manual - French - 21 pages

Powerplus POWX07582 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info