645078
7
Zoom out
Zoom in
Previous page
1/10
Next page
POWX0650 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
7.4 Adjusting the case width (Fig. 4, Fig. 5, Fig. 6, Fig. 7)
The machine is supplied with four spacer rings (15) which are each approximately 10 mm
thick. The chase width can be adjusted by varying the amount of spacer rings fitted
between the diamond cutting discs. The chase width can be calculated by taking into
account the thickness of the spacer rings and the width of the diamond cutting discs. The
maximum chase width is approximately 44mm.
7.5 Dust extraction
The machine may only be operated when connected to a suitable vacuum device, the
vacuum device must be approved for stone dust. A dust extraction adapter (3) is supplied,
ensure that the hose is securely attached to the adapter. Stop work immediately when the
vacuum device breaks down. Switch the machine off and restore the vacuum device. The
vacuum device must be suitable for the type of material you work with. Use a special
vacuum device when working with toxic materials or where toxic dust is produced. Use of
a household vacuum cleaner may damage your health.
For best results use a wet and dry vacuum device fitted with an appropriate filter. If in
doubt seek expert advice.
8 OPERATION
Mark the line of cut before starting work, hold the machine tightly with both
hands. (Fig. 8)
1. Set the chase depth. Place the front roller wheel of this machine firmly against the wall.
Switch the machine on and gently lower the machine towards the wall until the rotating
diamond cutting discs plunge into the wall, hold the machine tightly with both hands.
2. Carry out the cut steadily, evenly and with moderate pressure appropriate to the material
being cut. Ensure you work in the correct direction! Always work against the direction of
rotation as shown on the machines protective guard to avoid the risk of the machine
being forced uncontrolled of the cut.
3. After completing the cut, retract the machine slightly, switch off and remove from the cut.
Allow the diamond cutting discs to stop before putting the machine down. Do not attempt
to brake the diamond cutting discs by applying lateral pressure.
Remove the remaining masonry in the chase using the masonry breaking tool provided.
It is not possible to make curved cuts with the machine as the diamond cutting discs may
seize in the cut.
Paving slabs or similar must be placed on a solid surface or be otherwise securely
supported before starting the cut to avoid breakage.
When cutting especially hard material, e.g. concrete with high gravel content, the diamond
cutting discs can overheat and become damaged. This is indicated by a ring of sparks that
rotates with the diamond discs. In this case, interrupt the cutting process and allow the
diamond discs to cool down by running the machine at no-load for a short time.
Noticeably decreasing work progress and a rotating spark ring indicate that the diamond
cutting discs have become blunt.
9 CLEANING AND MAINTENANCE
WARNING: Disconnect the unit from the mains before carrying out any
maintenance or adjustments.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0650 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0650

Powerplus POWX0650 User Manual - German - 12 pages

Powerplus POWX0650 User Manual - Dutch - 11 pages

Powerplus POWX0650 User Manual - French - 11 pages

Powerplus POWX0650 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info