645078
6
Zoom out
Zoom in
Previous page
1/10
Next page
POWX0650 EN
Copyright © 2016 VARO P a g e | 6 www.varo.com
7.1 Fitting/changing the diamond cutting discs (Fig. 1 and Fig. 2)
Use only diamond cutting discs suitable for dry cutting, which are approved for use with the
material you wish to cut. Cutting discs must have a maximum permitted speed at least equal
to the machine’s maximum no-load speed.
Place the machine on a stable workbench with the diamond discs over the edge of the
table.
Set the cutting depth to the lowest position (maximum cutting depth) by using the lock
lever for depth stop (9) (Refer to “Depth adjustment” section).
Bring the protective guard down, this makes it easier to operate.
Push the spindle lock button (2) towards the motor housing as the arrow shows in Fig. 1
(A) and firmly hold it.
Loosen the flange nut with spindle sleeve (16) using the pin spanner (17), remove the
diamond cutting disc s(12) and the spacer rings (15). Then clean the motor flange (14),
the spacer rings and the flange nut with spindle sleeve.
Place a new diamond cutting disc onto the motor flange (14), followed by any remaining
space rings (15). (Refer to Fig. 2)
Slide the remaining diamond cutting disc on the spindle, screw the flange nut onto the
spindle.
Press the spindle lock button (2) and tighten the flange nut using the pin spanner.
CAUTION! Always replace diamond cutting discs in pairs.
7.2 Depth adjustment (Fig. 3)
WARNING: Disconnect the machine from the mains before any assembly
and adjustment.
Loosen the lock lever for depth stop (9) and set the required depth along the cutting depth
scale (10). Select a chase depth approximately 3mm deeper than the actual required
depth to compensate for unevenness in the wall surface.
Re-tighten the lock lever (9).
7.3 Turning the machine on/off
Press the safety switch (5) and push the ON/OFF switch trigger (4), the machine is on.
Release the trigger, the machine is off.
CAUTION! Always run the machine at no load for at least 30 seconds before
starting work. Damaged, out-or-round or vibrating diamond cutting discs
may not be used.
Soft start: The machine is fitted with a soft start mechanism.
Overload protection: The machine has an overload protection device and automatically
switches off when overloaded. Release the trigger and remove the machine from the
work-piece, restart and run the machine at no-load for approximately one minute to cool
the machine down.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0650 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0650

Powerplus POWX0650 User Manual - German - 12 pages

Powerplus POWX0650 User Manual - Dutch - 11 pages

Powerplus POWX0650 User Manual - French - 11 pages

Powerplus POWX0650 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info