641858
7
Zoom out
Zoom in
Previous page
1/13
Next page
POW8562 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
Insert the stop plate (A) into the gaps of the angle adjustment (B) with both adjusting
screws (C), push into the required position and tighten the adjusting screws.
Push the gliding bar (D) of the mitre angle stop into the required bar of the table surface.
Note: Whether you insert the stop plate (A) with the long side upwards or
downwards is determined by the height of the workpiece.
Right-handed operators prefer to push the mitre angle stop into the left bar
of the table surface.
7.5 Mounting the saw blade guard (Fig. 5)
Risk of injury! The saw blade must be lowered as far as possible in order to
avoid injury.
Push the bolt (26) onto the saw blade protection (8) and hold firm.
Position the saw blade protection on the splitting wedge (9) so that bolt (26) engages in
the groove. Then release the bolt.
7.6 Mounting the extraction (Fig. 6)
Screw the suction nozzle (27) to the housing using 4 Philips head screws M4×10 (28).
Place the vacuum hose (6) on the connecting piece of the saw blade guard (8).
Put the vacuum hose (6) on the vacuum connecting piece (27) on the rear of the device
8 OPERATION
Risk of injury! In the event of a functional fault, immediately press the red
button 0 on the On / Off switch and unplug.
8.1 Check before starting the device!
Risk of injury! The device may only be put into operation if there are no
defects. If a part is defective danger it must be replaced before the device is
used again.
Check to make sure the device is in safe operating condition:
Check to make sure there are no visible defects.
Check to make sure all device components are correctly mounted.
Check to make sure the safety equipment is functioning properly.
Check to make sure that the saw blade runs freely.
Check whether the adjusting screw for setting the angle of tilt is tightened.
8.2 Operating elements
8.2.1 On/off switch
Switching on: Pressing the green button I on the On / Off switch (1) switches on the saw.
Before starting to saw, wait until the blade has reached maximum speed.
Switching off: Pressing the red button 0 on the On / Off switch (1) switches off the saw.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW 8562 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW 8562 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW 8562

Powerplus POW 8562 User Manual - German - 14 pages

Powerplus POW 8562 User Manual - Dutch - 20 pages

Powerplus POW 8562 User Manual - French - 14 pages

Powerplus POW 8562 Additional guide - All languages - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info