641858
8
Zoom out
Zoom in
Previous page
1/13
Next page
POW8562 EN
Copyright © 2016 VARO P a g e | 8 www.varo.com
8.2.2 Overload Protection (5)
The machine is fitted with an overload protection (5). Allow the machine to cool down for at
least 30 minutes before switching it on again. For this first press the black button next to the
switch, then press the green button (1) to restart the machine.
8.2.3 Setting mechanism for the tilt angle
The saw blade can be set to any angle between 0° and 45°.
8.2.4 Hand crank for setting the cutting height
The cutting height of the saw blade must be adjusted to the height of the workpiece. The saw
blade must always be set to one blade tooth higher than the workpiece.
Note: In order to make use of the full range of 45° settings, the cutting
height must be reduced accordingly.
8.3 Workpiece stops
8.3.1 Mitre angle stop
The stop can be adjusted by a maximum of 120mm for mitre cutting.
Risk of injury! Do not push the stop (Fig. 4 A) too far in the direction of the
saw blade. The gap between the stop (Fig. 4 A) and the saw blade should be
approximately 2 cm.
8.3.2 Mitre cuts (Fig. 7)
Push the mitre angle stop (12) into the required bar of the table surface.
Loosen adjusting screw (A), set the required angle and then tighten the adjusting screw
again.
If necessary, push the stop plate backwards or forwards. For this, loosen both adjusting
screws (B), push stop plate (C) and then retighten adjusting screws (B).
8.3.3 Setting the stop rail of the parallel stop
The stop rail can be removed and repositioned after both wing nuts have been loosened:
High stop edge:
To saw tall workpieces.
Low stop edge:
To saw flat workpieces.
If the saw blade is angled.
8.3.4 Parallel stop
Loosen the locking lever (11) by turning the knob.
Set the parallel stop to the required cutting width by pushing on the scale.
Press down the locking lever (11).
8.4 Setting the cutting height (Fig. 8)
Risk of injury! Parts of the body or objects located in the adjustment area
may be caught by the operating saw blade! Only adjust the cutting height
when the saw blade is at a standstill!
Adjust the cutting depth by turning the hand crank (A).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW 8562 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW 8562 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW 8562

Powerplus POW 8562 User Manual - German - 14 pages

Powerplus POW 8562 User Manual - Dutch - 20 pages

Powerplus POW 8562 User Manual - French - 14 pages

Powerplus POW 8562 Additional guide - All languages - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info