628495

Polycom Vortex EF2280 Manual

23
Zoom out
Zoom in
Previous page
1/105
Next page
F01AGCMIN1?
Query the AGC minimum
gain on input channel 1 .
F01AGCMIN1x where x is a number between -15 and
0, depending on the current setting of the AGC
minimum gain on input channel 1 .
F01AGCMIN*-6
Set AGC minimum gain on
input channels 1-8 to -6 dB.
F01AGCMIN*~~~~~~~~
F01AGCMIN*ääääüüüü
Set AGC minimum gain on
input channels 1-4 to 0 dB
and AGC minimum gain on
input channels 5-8 to -3 dB.
F01AGCMIN*ääääüüüü
F01AGCMIN*?
Query AGC minimum gain on
input channels 1-8.
F01AGCMIN*abcdefgh, where a-h are each between
u and ä, depending on the current setting of the AGC
minimum gain for each of the eight input channels.
8.7. AGCRATE -- Set Ramp Rate of Mic/Line Input AGC
This command sets or queries the maximum rate at which the AGC can increase or decrease the gain of the
signals on input channels 1-8 . The ramp rate is expressed in dB/sec.
This command is a channel integer command. See
Section 6.3 and Section 6.2 for more information on this type
of command. The minimum and maximum values for this command are 1 and 5, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will be
restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
F01AGCRATE13
Set AGC ramp rate on input
channel 1 to 3 dB/sec.
F01AGCRATE13
F01AGCRATE1?
Query the AGC ramp rate
on input channel 1 .
F01AGCRATE1x where x is a number between 1 and 5,
depending on the current setting of the AGC ramp rate
on input channel 1 .
F01AGCRATE*5
Set AGC ramp rate on input
channels 1-8 to 5 dB/sec.
F01AGCRATE*ëëëëëëëë
F01AGCRATE*ààààêêêê
Set AGC ramp rate on input
channels 1-4 to 1 dB/sec
and AGC ramp rate on
input channels 5-8 to 4
dB/sec.
F01AGCRATE*ààààêêêê
F01AGCRATE*?
Query AGC ramp rate on
input channels 1-8.
F01AGCRATE*abcdefgh, where a-h are each between
à and ë, depending on the current setting of the AGC
ramp rate for each of the eight input channels.
8.8. AMASGN -- Assign Inputs to an Automixer
This command is used to assign one of the mic/line inputs (1-8) to an internal automixers. Setting AMASGN to 0
for a given input channel corresponds to no automixer, 1 corresponds to Automixer #1 , and 2 corresponds to
automixer #2.
An AMASGN command usually removes a microphone from one automixer and adds it to another. If the
microphone is removed from an automixer where it was assigned as the "Last Mic On" and list mic mode
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2280 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2280

Polycom Vortex EF2280 User Manual - English - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info