Manual Parkside ULG 3.8 B1 - IAN 113043 (page 8 of 60) (English, German, Dutch, Danish, French, Swedish, Finnish)

679451

8

Zoom out

Zoom in

Previous page

1/60

Next page

5

ULG 3.8 B1

GB

IE

♦ Remove the positive terminal clamp (red) of

the charger from the positive terminal on the

battery.

Select charging mode

You can choose between diﬀerent charging modes

for charging various batteries at diﬀerent ambient

temperatures.

Unlike standard battery chargers, this appliance has

a special function for reusing an empty chargeable

battery or accu. You can recharge a completely dis-

charged battery/accu. A protection function against

incorrect connection and short circuiting ensures

safe charging. Due to the installed electronics, the

charger does not begin operation directly after

connecting the battery, but only starts after a

charging mode has been selected.

This prevents sparking, which often occurs when

connecting. In addition, the battery charger is con-

trolled by an internal MCU (micro-computer unit).

Reset/deleting settings

♦ After connection to the power supply, the appli-

ance automatically returns to its initial state and

remains in Standby mode

Switching between modes 1, 2, 3

and 4

Press the MODE selection button a corresponding

amount of times.

The appliance switches through the modes in the

following order: Standby ( ), Mode 1 ( ), Mode

2 (

), Mode 3 ( ), Mode 4 ( ) and then starts

the next cycle.

NOTE

► If you press the MODE selection button

, the

charging mode automatically switches to the next

mode and begins operation in that mode. If a

12V battery is connected, Mode 1 ( ) is not

selectable. If a 6V battery is connected, Mode

2 (

) 3 ( ) and 4 ( ) are not selectable. If

a battery is not disconnected from the charging

station after a full charge, the appliance remains

in trickle-charge mode, even if the user switches

over to another mode. This protects the fully

charged battery from being damaged.

Mode 1 “6V” (7.3V/0.8A)

This mode is suitable for charging 6V lead-acid

batteries with a capacity below 14Ah.

♦ Press the selection button MODE

, to activate

Mode 1 ( ). After doing so, the corresponding

LED display

lights up. If you do not acti-

vate another process afterwards, the electronic

system will automatically activate together with

the LED display and starts the charging

process.

If the procedure runs without any problems,

the LED display remains on during the

entire charging process, until the battery is fully

charged to 7.3V/± 0.25V. When the battery

is fully charged, the LED display lights

up and the LED display goes out.

The appliance now switches automatically into

trickle charging mode.

Mode 2 “12V” (14.4V/0.8A)

This mode is suitable for charging 12V lead-acid

batteries with a capacity below 14Ah.

♦ Press the MODE selection button

, to activate

Mode 2 (

). After doing so, the corresponding

LED display

lights up. If you do not acti-

vate another process afterwards, the electronic

system will automatically activate together with

the LED display and starts the charging

process.

If the procedure runs without any problems,

the LED display remains on during the

entire charging process, until the battery is fully

charged. When the battery is fully charged,

the LED display lights up and the LED

display goes out.

The appliance now switches automatically into

trickle charging mode.

Mode 3 “12V” (14.4V/3.8A)

This mode is mainly used for charging 12V lead-

acid batteries with a large capacity of more than

14 Ah under normal conditions.

♦ Press the MODE selection button

, to activate

Mode 3 (

). If you do not activate another

process afterwards, the electronic system will

activate together with the LED display

and starts the charging process.

1

Hello,
I am using this charger to continueously charge a (car-)battery which I am using to feed some outdoor LED lighting at night.
Since a few weeks I sometimes see the intensity of the light go up and down.
When I look at the charger, I see that the Red Led indicator "Charging" and the Green Led indicator "Fully Charged" flash alternately!
When I then remove the charger from the power for one day, the other day it is functioning normally again.
But after a few days it happens again!
Can somebody tell me, what's the cause of this "flashing"?
Wil van Woerkom (The Netherlands)
Email address: wvwoerkom@rolluik-deur-specialist.nl Submitted on 22-5-2022 at 13:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Parkside ULG 3.8 B1 - IAN 113043 at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside ULG 3.8 B1 - IAN 113043 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 0,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info