Manual Parkside ULG 3.8 B1 - IAN 113043 (page 7 of 60) (English, German, Dutch, Danish, French, Swedish, Finnish)

679451

Zoom out

Zoom in

1/60

ULG 3.8 B1

RISK OF CHEMICAL BURNS!

■ Wear safety goggles! Wear

protective gloves! If your eyes or

skin come into contact with battery

acid, rinse the aﬀected part of the

body with plenty of clear running

water and seek immediate medical

assistance!

■ Avoid an electric short-circuit when

connecting the charger to the bat-

tery. Connect the negative terminal

connecting cable to the negative ter-

minal of the battery or to the vehicle

bodywork/earth only. Connect the

positive terminal connecting cable

only to the positive terminal of the

battery!

■ Do not set up the charger near a

ﬁre or subject it to heat or to long-

term temperatures exceeding 50°C!

■ When attaching the charger, be

sure not to damage any lines for

fuel, electricity, braking system,

hydraulics or water with screws!

■ Do not cover the charger with objects

of any kind!

■ Protect the electrical contacts of the

battery against short-circuiting!

■ Use the charger exclusively for

charging or trickle charging undam-

aged 6V/12V lead batteries! Fro-

zen batteries may not be charged.

Operation

Before ﬁrst use

♦ Before connecting the battery charger, read the

operating instructions of the battery thoroughly.

♦ In addition, observe the vehicle manufacturer’s

instructions for a permanently connected bat-

tery. Secure the vehicle; turn oﬀ the ignition.

♦ Clean the battery terminals. Ensure that no dirt

comes into contact with your eyes in the process.

♦ Provide for suﬃcient ventilation.

Connection

NOTE

►

There are two options for connecting the charger.

Connect the negative terminal connecting cable

(black) either directly to the negative terminal of

the battery or to the bodywork. Please also bear

in mind the vehicle manufacturer’s instructions.

♦ Before starting the charging or trickle charging

procedure on a permanently installed battery in

a vehicle, ﬁrst disconnect the negative terminal

connecting cable (black) of the vehicle from the

negative terminal of the battery. The negative

terminal of the battery is usually connected to

the vehicle’s bodywork/earth.

♦ Then disconnect the positive terminal connect-

ing cable (red) of the vehicle from the positive

terminal of the battery.

♦ Clamp the positive terminal clamp (red)

of the

charger to the positive terminal on the battery.

♦ Clamp the negative terminal clamp (black)

the charger to the negative terminal on the battery

or to the bodywork.

♦ Connect the mains cable of the battery

charger to the power socket.

♦ If the terminal clamps are connected incorrectly,

the LED display “ERROR”

will light up.

Disconnecting

♦ Disconnect the appliance from the power supply.

♦ Remove the negative terminal clamp (black)

of the charger from the negative terminal on the

battery or from the bodywork.

Hello,
I am using this charger to continueously charge a (car-)battery which I am using to feed some outdoor LED lighting at night.
Since a few weeks I sometimes see the intensity of the light go up and down.
When I look at the charger, I see that the Red Led indicator "Charging" and the Green Led indicator "Fully Charged" flash alternately!
When I then remove the charger from the power for one day, the other day it is functioning normally again.
But after a few days it happens again!
Can somebody tell me, what's the cause of this "flashing"?
Wil van Woerkom (The Netherlands)
Email address: wvwoerkom@rolluik-deur-specialist.nl Submitted on 22-5-2022 at 13:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside ULG 3.8 B1 - IAN 113043 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 0,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside ULG 3.8 B1 - IAN 113043 Manual

Product: