706372

Parkside PZKS 1500 B2 - IAN 280657 Manual

98
Zoom out
Zoom in
Previous page
1/106
Next page
93GB / IE / NI
- Attach the miter lock handle (10) to the
turntable (15).
- When fixing the saw to the workbench,
insert the mounting screws (not included)
through the mounting holes (16a).
•Inordertoadjusttheturntable(15)
loosen the mitre lock handle (10) approx.
2 turns.
•Pressthemitredetentlever(11)andturn
the turntable (15) and pointer (12) to the
desired angle measurement on the scale
(14), release the mitre detent lever (11)
and secure with the mitre lock handle
(10).
•Pressingthemachinehead(4)lightly
downwards and removing the fastening
bolt (30) from the motor bracket at the
same time disengages the saw from the
lowest position.
•Swingthemachinehead(4)upuntilthe
release lever (3) latches into place.
•Itispossibletosecuretheclamping
device (7) to the left or right on the
stationary saw bench. Insert the clamping
device (7) in the hole on the rear side of
the stop rail (17) and secure it with the
grip screw (28).
•Attachtheworkpiecesupports(8)tothe
fixed saw table (16) as shown in Figure
5 and fasten with the screw (29).
•Itispossibletotiltthemachinehead(4)
a max. 45° to the left by loosening the
locking screw (27).
8.2 Mitre angle setting
•Ninepositivemiterdetentsareprovided
for fast and accurate preset miter angles
– locations are at 45°, 30°, 22.5°, 15°
left and right, and center at 0°.
•Followtheprocessformitreanglesetting.
•Unlocktheturntablebyturningthemitre
lock handle (10) counter-clockwise.
•Movetheturntablewhilepressthemitre
detent lever (11) to align the mitre angle
pointer (12) to the desired degree on the
mitre angle scale (14).
•Ifthedesiredangleisoneofthenine
positive mitre detents, release the mitre
detent lever (11), making sure the lever
snaps into position, and then secure by
tightening the mitre lock handle (10).
•Ifthemitreangledesiredisnotoneofthe
nine positive mitre detents, simply lock
the turntable into desired angle position
by turning the mitre lock handle (10) in
the clockwise direction.
8.3 Precision adjustment of the
blade for crosscut 90°
(Fig. 1/2/6/7)
• Nostopangleincluded.
• Movethehead(4)inposition,sothat
the blade (6) rests directly above the
turntable (15). Now, use locking screw
(25) to lock the drag guide (26).
• Lowerthemachinehead(4)andsecure
using the fastening bolt (30).
•Loosenthebevellockingscrew(27).
•Positiontheanglestop(a)betweenthe
saw blade (6) and the turntable (15).
•Releasethelockingnut(c)andadjust
the adjusting screw (32) until the angle
between the saw blade (6) and turntable
(15) is 90°.
•Re-tightenthelockingnut(c).
•Subsequentlycheckthepositionofthe
angle indicator. If necessary loosen the
pointer (24) using a Philips screwdriver,
set to position 0° on the angle scale (23)
and re-tighten the retaining screw.
8.4 Precision adjustment of stop
rail for crosscut 90°
(Fig. 1/8/9)
- Bring the power tool into the working
position.
- Turn the turntable (15) to the 0° on the
mitre angle scale (14). The metre detent
lever
（
11
）
must be felt to engage in
the detent.
Attachment and operation
… 98 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PZKS 1500 B2 - IAN 280657 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 1500 B2 - IAN 280657 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info