706372

Parkside PZKS 1500 B2 - IAN 280657 Manual

99
Zoom out
Zoom in
Previous page
1/106
Next page
94
GB / IE / NI
Checking:
(see figure 9)
- Adjust an angle gauge to 90° and
position it between the stop rail (17) and
the saw blade (6) on the turntable (15).
The leg of the angle gauge must be flush
with the saw blade (6) over the complete
length.
Adjusting:
(see figure 8/9)
- Loosen all four set screws (33) and turn
the stop rail (17) until the leg of the angle
gauge is flush with the stop rail over the
complete length.
- Retighten the four set screws again.
When the mitre angle pointer (12) is not
in line with the 0° mark of mitre angle
scale (14) after adjusting, loosen the
screw on the mitre angle pointer (12)
with a philips screwdriver and align the
angle pointer pointed to the 0°mark.
8.5 Cross cut 90° and turntable 0°
(Fig. 10/12)
In the case of cutting widths up to approx.
100 mm it is possible to fix the traction
function of the saw with the locking screw
(25) in the rear position. In this position the
machine can be operated in cross cutting
mode. If the cutting width is over 100 mm
then it is necessary to ensure that the locking
screw (25) is loose and the machine head (4)
can move.
•Movethemachinehead(4)toitsupper
position.
•Usethehandle(1)topushbackthe
machine head (4) and fix it in this
position if required(dependent on the
cutting width).
•Placethepieceofwoodtobecutatthe
stop rail (17) and on the turntable (15).
•Lockthematerialwiththeclamping
device (7) on the fixed saw table(16) to
prevent the material from moving during
the cutting operation.
•Operatethereleaselever(3)torelease
the machine head (4).
•PresstheON/OFFswitch(2)tostartthe
motor.
• Withthedragguide(26)fixedinplace:
• Usethehandle(1)tomovethemachine
head (4) steadily and with light pressure
downwards until the saw blade (6) has
completely cut through the work piece.
• Withthedragguide(26)notfixedin
place:
• Pullthemachinehead(4)alltheway
to the front. Lower the handle (1) to the
very bottom by applying steady and
light downward pressure. Now push the
machine head (4) slowly and steadily to
the very back until the saw blade (6) has
completely cut through the work piece.
• Whenthecuttingoperationiscompleted,
move the machine head (4) back to its
upper (home) position and release the
ON/OFF switch (2).
Attention! The machine executes an upward
stroke automatically due to the return
spring, i.e. do not release the handle (1)
after completing the cut; instead allow the
machine head to move upwards slowly
whilst applying light counter pressure.
8.6 Cross cut 90° and metre cut 0°
- 45° (Fig. 10/11)
The crosscut saw can be used to make
crosscuts of 0° -45° to the left and 0° - 45° to
the right in relation to the stop rail.
•Loosenthemetrelockhandle(10)incase
it is tightened, press the metre detent
lever (11) and use the mitre lock handle
(10) to adjust the turntable (15) to the
desired angle. The mitre angle pointer
(12) on the turntable must match the
desired angle on the mitre angle scale
(14) on the fixed saw table (16).
•Re-tightenthemitrelockhandle(10)in
order to secure the turntable (15).
Attachment and operation
… 99 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PZKS 1500 B2 - IAN 280657 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 1500 B2 - IAN 280657 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info