Manual Parkside PTS 500 C3 - IAN 286507 (page 31 of 132) (English, German, Dutch, French, Portuguese, Spanish)

706354

Zoom out

Zoom in

1/132

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse

and / or incorrect operating procedures or

conditions and can be avoided by taking proper

precautions as given below.

1. Maintain a ﬁrm grip on the power

tool and position your body and

arm to allow you to resist kickback

forces. Always use auxiliary handle,

if provided, for maximum control

over kickback or torque reaction

during start-up. The operator can control

torque reactions or kickback forces, if proper

precautions are taken.

2. Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

3. Do not position your body in line

with the rotating wheel. Kickback will

propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

4. Use special care when working

corners, sharp edges etc. Avoid

bouncing and snagging the

accessory. Corners, sharp edges or

bouncing have a tendency to snag the

rotating accessory and cause loss of control

or kickback.

5. Do not attach a saw chain,

woodcarving blade, segmented

diamond wheel with a peripheral

gap greater than 10 mm or toothed

saw blade. Such blades create frequent

kickback and loss of control.

6. Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the loading

and susceptibility to twisting or binding of

the wheel in the cut and the possibility of

kickback or wheel breakage.

7. When wheel is binding or when

interrupting a cut for any reason,

switch oﬀ the power tool and hold

the power tool motionless until the

wheel comes to a complete stop.

Never attempt to remove the wheel

from the cut while the wheel is in

motion otherwise kickback may

occur. Investigate and take corrective action

to eliminate the cause of wheel binding.

8. Do not restart the cutting operation

in the workpiece. Let the wheel

reach full speed and carefully re-

enter the cut. The wheel may bind, walk

up or kickback if the power tool is restarted in

the workpiece.

9. Support panels or any oversized

workpiece to minimize the risk of

wheel pinching and kickback. Large

workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

10. Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Safety warnings for diamond discs

1. Cutting-oﬀ tools are very fragile and likely to

break which is why great care must be taken

when handling the cutting-oﬀ tools. Using

damaged, incorrectly clamped or incorrectly

installed cutting-oﬀ tool is dangerous and may

cause serious injury.

2. Cutting-oﬀ tools are to be treated with care

and transported carefully. Cutting-oﬀ tools

should be stored in such a way that they

are not exposed to mechanical damage or

harmful environmental inﬂuences.

Laser safety warnings

WARNING! PRODUCT YOURSELF

FROM LASER RADIATION!

P max.: < 1 mW, λ: 650 nm

EN 60825-1:2014

This product contains a Class 2 laser.

33 GB / IE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTS 500 C3 - IAN 286507 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 4,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTS 500 C3 - IAN 286507 Manual

Product: