706354

Parkside PTS 500 C3 - IAN 286507 Manual

30
Zoom out
Zoom in
Previous page
1/132
Next page
4. Wheels must be used only for
recommended applications. For
example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side
forces applied to these wheels may cause
them to shatter.
5. Always use undamaged wheel
flanges that are of correct diameter
for your selected wheel. Proper wheel
flanges support the wheel thus reducing the
possibility of wheel breakage.
6. The outside diameter and the
thickness of your accessory must be
within the capacity rating of your
power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
7. The arbour size of wheels and
flanges must properly fit the spindle
of the power tool. Wheels and flanges
with arbour holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
8. Do not use damaged wheels.
Before each use, inspect the
wheels for chips and cracks. If
power tool or wheel is dropped,
inspect for damage or install an
undamaged wheel. After inspecting
and installing the wheel, position
yourself and bystanders away from
the plane of the rotating wheel and
run the power tool at maximum no
load speed for one minute. Damaged
wheels will normally break apart during this
test time.
9. Wear personal protective
equipment. Depending on
application, use face shield, safety
goggles or safety glasses. As
appropriate, wear dust mask,
hearing protectors, gloves and shop
apron capable of stopping small
abrasive or workpiece fragments.
The eye protection must be capable of
stopping flying debris generated by various
operations. The dust mask or respirator must
be capable of filtrating particles generated by
your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
10. Keep bystanders a safe distance
away from work area. Anyone
entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken wheel
may fly away and cause injury beyond
immediate area of operation.
11. Hold the power tool by insulated
gripping surfaces only, when
performing an operation where
the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live”
and could give the operator an electric shock.
12. Position the cord clear of the
spinning accessory. If you lose control,
the cord may be cut or snagged and your
hand or arm may be pulled into the spinning
wheel.
13. Never lay the power tool down
until the accessory has come to a
complete stop. The spinning wheel may
grab the surface and pull the power tool out
of your control.
14. Do not run the power tool while
carrying it at your side. Accidental
contact with the spinning accessory could
snag your clothing, pulling the accessory into
your body.
15. Regularly clean the power tool’s
air vents. The motor’s fan will draw
the dust inside the housing and excessive
accumulation of powdered metal may cause
electrical hazards.
16. Do not operate the power tool near
flammable materials. Sparks could
ignite these materials.
17. Do not use accessories that require
liquid coolants. Using water or other
liquid coolants may result in electrocution or
shock.
Further safety instructions for abrasive
cutting-off operations - Kickback and
related warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel. Pinching or snagging
causes rapid stalling of the rotating wheel which
in turn causes the uncontrolled power tool to be
forced in the direction opposite of the wheel’s
rotation at the point of the binding.
32 GB / IE
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTS 500 C3 - IAN 286507 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTS 500 C3 - IAN 286507 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 4,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info