595353

Parkside PTBM 500 A1 - IAN 102855 Manual

11
Zoom out
Zoom in
Previous page
1/58
Next page
11
IEGB
- All hoods and protective devices
must be assembled properly be-
fore commissioning.
- Disconnect the mains plug be-
fore changing the setting on the
device.
Setting up
Place the bench drill on a solid surface.
Ideally, bolt the drill to the surface. Use the
two holes in the baseplate (17) for this.
Selecting the speed
1. Release the locking bolt (11) on the
gear cover (8).
2. Open the gear cover (8).
3. Release the retaining bolt (13) on the
motor unit (14).
4. Slide the motor unit (14) forward a little
to release the load on the V-belt (26).
5. Place the V-belt (26) on the desired as-
sembly to reach the specied speed:
Ø [mm]: Ø [mm]:
[1/min]:
6 - 8 9 - 10
> 8 > 10
< 3 < 4
3 - 4 5 - 6
5 7 - 8
6. Slide the motor unit (14) back to tensi-
on the V-belt (26) again.
7. The V-belt (26) is correctly tensioned
when it gives way slightly when
pressed.
8. Tighten the retaining bolt (13) on the
motor unit (14) again.
9. Close the gear cover (8). Fasten the
locking bolt (11) on the gear cover .
The gear cover (8) is equipped with
a safety switch (27). If the gear
cover (8) is not closed correctly, the
device cannot be switched on.
Recommended speeds for
different drill sizes and materials:
Ø [mm]: Ø [mm]:
[1/min]:
6 - 8 9 - 10
> 8 > 10
< 3 < 4
3 - 4 5 - 6
5 7 - 8
Checking the V-belt
1. Release the locking bolt (11) on the
gear cover (8).
2. Open the gear cover (8).
3. Check the tension of the V-belt (26).
4. The V-belt (26) is correctly tensioned
when it gives way slightly when
pressed.
5. Check the V-belt (26) for tears, cuts or
other damage.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTBM 500 A1 - IAN 102855 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTBM 500 A1 - IAN 102855 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PTBM 500 A1 - IAN 102855

Parkside PTBM 500 A1 - IAN 102855 User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info