595353

Parkside PTBM 500 A1 - IAN 102855 Manual

12
Zoom out
Zoom in
Previous page
1/58
Next page
12
GB IE
6. Close the gear cover (8). Fasten the
locking bolt (11) on the gear cover (8).
Tensioning the V-belt
1. Release the locking bolt on the gear
cover (8).
2. Open the gear cover (8).
3. Release the retaining bolt (13) on the
motor unit (14).
4. Slide the motor unit (14) back to tensi-
on the V-belt (26).
5. The V-belt (26) is correctly tensioned
when it gives way slightly when
pressed.
6. Tighten the retaining bolt (13) on the
motor unit (14) again.
7. Close the gear cover (8). Fasten the
locking bolt (11) on the gear cover (8).
Adjusting the Drilling Bench
1. Release the clamping bolt (24).
2. Push the drilling bench (20) to the desi-
red height.
3. Pivot the drilling bench (20) to the desi-
red position.
4. Fasten the drilling bench (20) again
with the clamping bolt (24).
5. You can also adjust the tilt angle of the
drilling bench (20). To do this, release
the clamping bolt (19) under the drilling
bench. Tilt the drilling bench (20) as
desired to the right or left up to a max.
of 45° and secure the drilling bench
(20) again with the clamping bolt (19).
Preselecting the Drilling Depth
1. Move the red arrow to the „0“ position
on the drilling depth scale (3).
2. Turn one of the drill lifting arms (9) an-
ticlockwise and move the spindle (6) to
the desired drilling depth.
3. Turn the xing nut to the desired point
on the depth scale. Read off the red ar-
row on the drilling depth scale to help
you.
4. Move the spindle (6) slowly back to the
stop position.
5. Adjust the drilling bench (20) until the
workpiece is resting against the drill tip.
Changing the Bit
Remove the plug from the mains
socket before changing the bit. This
will prevent an accidental start-up.
1. Fold the safety device (7) up.
2. Release the retaining jaws of the drill
chuck (4) with the drill chuck key (29).
3. Remove the bit.
4. Insert a new bit.
5. Tighten the retaining jaws of the drill
chuck (4) with the drill chuck key (29).
6. Check that the bit is centred.
7. Fold the safety device (7) down again.
Under no circumstances must you
leave the drill chuck key (29) inser-
ted.
Drilling
1. Turn the appliance on.
2. Turn one of the drill lifting arms (9) an-
ticlockwise
3. The drill chuck (4) is lowered.
4. Drill into the workpiece at the appropri-
ate feed rate and to the desired depth.
5. Be aware of any necessary chip brea-
king on the way to the desired depth.
6. Move the bit slowly back to the stop
position.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTBM 500 A1 - IAN 102855 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTBM 500 A1 - IAN 102855 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PTBM 500 A1 - IAN 102855

Parkside PTBM 500 A1 - IAN 102855 User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info