595353

Parkside PTBM 500 A1 - IAN 102855 Manual

13
Zoom out
Zoom in
Previous page
1/58
Next page
13
IEGB
General Information
The feed rate and spindle speed
are decisive for the service life of
the bit.
- The cutting speed is determined by the
speed of the drill spindle and by the
diameter of the bit.
- In principle, therefore, the larger the
bit diameter, the lower the speed that
should be selected.
- For workpieces of greater strength, the
cutting pressure must be higher.
- Repeated withdrawal of the bit enables
easier chip removal.
- Chip removal is especially difcult in
deep holes. Reduce the feed rate and
speed in this case.
- To avoid excessive wear on the cutting
surface of the bit, for drill holes over
8.0 mm in diameter you should rst
drill with a bit with a smaller diameter.
Switching on and off
Make sure that the power supply
voltage matches the voltage rating
indicated on the device‘s type pla-
te.
Connect the machine to the power
supply.
Switching on:
Press the on switch (2).
Switching off:
Press the off switch (1).
Emergency stop:
Press the emergency stop button (5).
After pressing the emergency stop
button, the emergency stop button
(5) must be activated again by
turning it. Press the on switch (2) to
restart the device.
Clamping the Workpieces
Only work with workpieces that can be
securely clamped. The workpiece must not
yield too much. Otherwise it is nor possib-
le to apply adequate tension.
The workpiece must not be too small or too
large either.
Removing Blockages
- You should always select a suitable
feed rate which allows trouble-free chip
breaking.
- If the bit is jammed in the workpiece,
turn off the power and unplug the po-
wer cord. Turn the bit on the drill chuck
anticlockwise with a little jerk to break
the chip and release the bit again.
- If a fragment is produced during the
processing of the workpiece, turn off
the power and unplug the power cord.
Use a pair of pliers and remove the
fragment to prevent it ying off in an
uncontrolled way.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PTBM 500 A1 - IAN 102855 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTBM 500 A1 - IAN 102855 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PTBM 500 A1 - IAN 102855

Parkside PTBM 500 A1 - IAN 102855 User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info