684713

Parkside PKGA 40-Li A1 - IAN 313870 Manual

54
Zoom out
Zoom in
Previous page
1/310
Next page
54
GB IE
1. Loosen the screw (48) on the carrying
harness eye with the hexagon socket
wrench (22) and tighten it slightly.
2. Depending on the cutting tool, balance
the tool according to the criteria men-
tioned above by moving the eyelet (6)
along the tube shaft (4).
3. Tighten the screw (48) when the device
is in the desired position.
Assemble the 3-tooth
blade
Whenever you use the 3-too-
th blade, the protective cover
without extension must be
used. (See Chapter: “Remo-
ving/mounting the protective
cover extension”)
1. Remove the rechargeable batteries.
2. Place the device on the ground in a
stable position.
3. Block the mounting spindle (52) using
the hexagon socket wrench (22) as de-
picted.
4. Place the 3-toothed blade onto the
mounting spindle (52). The blade can
be used on both sides.
5. Fasten the blade using the thinner was-
her (53), conical spring washer (54)
and nut (55).
Insert the nut (55) into the conical
spring washer (54) as shown.
Use the assembly key (23) to secure it.
6. Remove the hexagon socket
wrench (22)!
Dismantling is carried out in reverse
order.
Mount the spool
The protective cover must be
mounted with the extension
when using the thread spool.
(See Chapter: “Removing/
mounting the protective co-
ver extension”)
Do not replace the non-me-
tallic laments of the spool
end with metallic laments!
Risk of injury!
1. Remove the rechargeable batteries.
2. Place the device on the ground in a
stable position.
3. Block the mounting spindle (52) using
the hexagon socket wrench (22) as de-
picted.
4. Place the thin washer (53) on the
mounting spindle (52).
5. Screw the spool cap (17) anticlock-
wise back onto the mounting spindle
(52).
Dismantling is carried out in reverse
order.
Extend the thread
Your device is equipped with a doub-
le-string activated touch control, i.e. the
two strings are extended when you tap the
cutting head on the ground.
1. Hold the device in operation over a
grassy area and lightly tap the cutting
head a few times on the ground. This
causes the thread to lengthen.
2. The protective cover (
A
15) inserted
into the protective cover (
A
14) cuts
the thread to the desired length.
… 54 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pkga-40-li-a1---ian-313870

Reset search

  • Bonjour. Je recherche un arbre de transmission de 64 cm de long et de 5 MM de diametre avec les.bout carré sur 2 cm de long pour une perche multifonction tailles haies électriques parkside Submitted on 3-8-2022 at 21:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKGA 40-Li A1 - IAN 313870 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGA 40-Li A1 - IAN 313870 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 5,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info