684713

Parkside PKGA 40-Li A1 - IAN 313870 Manual

51
Zoom out
Zoom in
Previous page
1/310
Next page
51
IEGB
1. Place the round handle (5) onto the
tubular shaft of the device housing (4).
Choose a position within the
levelled adjustment range mar-
ked on the bottom of the tubu-
lar shaft.
2. Position the leg protection (7) onto the
round handle (5) from below.
3. Fix the round handle (5) and the leg
protection (7) with the four hexagon
socket screws (32) using the hexagon
socket wrench (21) from the
storage (
A
31).
Mounting the saw chain
Pay attention to the correct rotation
direction of the saw chain. This is
indicated on the chain wheel cover
(33) and above the bar bolt (37).
Tension the saw chain in accor-
dance with the rst 5-6 steps.
1. Place the device on a level surface.
2. Remove the chain wheel cover (33) by
loosening the nut (34) with the moun-
ting key (23).
3. Place the sawing chain (1) into the bla-
de groove. Place the sawing chain (1)
into the chain sprocket (36).
4. Place the blade bar (35) and saw
chain (1) onto the rail bolts (37). When
the nose on the right below the guide
bolt (37) sits in the lower round recess
on the blade bar, the blade bar is pla-
ced correctly. It is normal for the saw
chain (1) to sag.
5. Pre-tension the saw chain (1) by turning
the screw (38) in a clockwise direction
with the mounting key (23).
6. Put the chain wheel cover (33) back in
position. Tighten the chain wheel cover
nut (34).
Caution! The pole-mounted pruner
can be prone to leaks.
Mounting the protective
cover
The protective cover (14) must be mounted
to the front tubular shaft (2) with the re-
tainer for spool and 3-tooth blade.
1. Screw the protective cover (14) to the
front tubular shaft (2) using the two
small Phillips screws (49). Use the Phil-
lips screwdriver (24) for this.
2. Fasten the cover (50) to the protective
hood (14). Use the hexagon socket
wrench (22) and the three screws (51).
Removing/mounting
the protective cover
extension
If using the 3-tooth blade, the protective
cover extension must be removed.
If using the spool, the extension must be
mounted.
Removing the protective cover
extension:
1. Unlock the lock for the protective cover
extension (56) using a Phillips-head
screwdriver on the side of the string
cutter (15).
2. Remove the protective cover extension
(56).
Mounting the protective cover
extension:
1. Slide the extension (56) onto the pro-
tective cover (14). Begin on the side
without the string cutter (15).
2. Slide the extension (56) up until it clicks
into place.
… 51 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-pkga-40-li-a1---ian-313870

Reset search

  • Bonjour. Je recherche un arbre de transmission de 64 cm de long et de 5 MM de diametre avec les.bout carré sur 2 cm de long pour une perche multifonction tailles haies électriques parkside Submitted on 3-8-2022 at 21:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKGA 40-Li A1 - IAN 313870 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKGA 40-Li A1 - IAN 313870 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 5,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info