595309
11
Zoom out
Zoom in
Previous page
1/76
Next page
8
PDEXS 150 B2
GB
IE
Refilling oil
To ensure that the compressed air-powered random
orbital sander remains operational for as long as
possible, make sure that there is sufficient pneu-
matic oil in the appliance.
The following options are available:
Attach a maintenance unit with an oiler to the
compressor.
Install a fitted oiler into the compressed air line
or the compressor.
Add 3–5 drops of pneumatic oil into the
connector nipple
every 15 minutes of
operation.
Connecting to a compressed air source
NOTE
Before connecting the compressed air source
the correct working pressure (3–6 bar)
must be fully reached
make sure that the trigger is in the upper
position
Attach the appliance to a compressor by con-
necting the connector nipple
with the supply
hose of the compressed air source.
To ensure that you can regulate the air pressure,
the compressed air source must be equipped
with a pressure reducer.
Handling
Switching on and off
Switching on:
First press the locking mechanism forwards and
then the trigger to switch the appliance on.
Switching off:
Let go of the trigger
.
When you have finished working, disconnect
the appliance from the compressed air source.
Regulation of vibration output
Use the speed controller to control the air-
flow and thus the vibration output (also during
operation).
The ideal speed depends on the material being
worked and can be determined through practical
tests.
Use the pressure reducer to set the correct working
pressure. Operate the appliance at a working pres-
sure of 6.3 bar.
Sanding
Switch on the compressed air source and allow
it to run until the maximum tank pressure has
been reached.
Use the pressure reducer on the compressed
air source to set the optimum working pressure.
Note that the maximum working pressure may
not be exceeded. An excessive working pressure
does not mean increased output; it merely in-
creases the air consumption and accelerates
appliance wear. Always comply with the techni-
cal information.
Switch on the compressed air-powered random
orbital sander.
Allow the device to reach the required speed
and adjust as necessary.
Guide the compressed air-powered random
orbital sander parallel onto the workpiece.
Move the appliance parallel and in flat circles
or alternatively lengthwise and across the sur-
face. Use the housing
as a handle to guide
the appliance in the desired direction.
Do not press the compressed air-powered ran-
dom orbital sander down. Pressing down hard
does not increase the working efficiency!
When you have finished working, let go of the
trigger
to switch off the appliance.
When you have finished working, disconnect
the appliance from the compressed air source.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDEXS 150 B2 - IAN 110141 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDEXS 150 B2 - IAN 110141 in the language / languages: English, German, Dutch, French, Swedish, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info