595309

Parkside PDEXS 150 B2 - IAN 110141 Manual

12
Zoom out
Zoom in
Previous page
1/76
Next page
9
PDEXS 150 B2
GB
IE
CAUTION!
► Sanding creates dust. Always wear protective
gloves, a suitable mask and clean the sand-
paper and workpiece at regular intervals with
a vacuum cleaner or compressed air.
► Suitable safety precautions must be taken
depending on the size and nature of the
workpiece. Use suitable clamping devices
to prevent the workpiece from slipping.
► In the event of an interruption to the air
supply, release the trigger
immediately.
Optimal working procedures
The most important thing to remember when sanding
is to use successively finer grained paper. With a
coarse grain, the surface will not become smooth,
but rather rougher. If the grain is too fine, you will
hardly achieve any noticeable result.
The material removal rate is determined by the
speed and grain size of the sandpaper.
The sandpaper used should be appropriate to the
substance being worked and the amount of material
to be removed.
CAUTION!
► Ensure that the appliance is disconnected
from the compressed air source before you
fit or remove a sandpaper disc
.
Material Grain
Paintwork: rubbing down 180
removing
scratches
120
removing rust 40
Wood: softwood 60–80
hardwood 60
plywood 240
Metal: aluminium 80
steel 60
Maintenance and cleaning
WARNING! RISK OF INJURY!
Disconnect the appliance from the
compressed air supply.
CAUTION!
► Before maintenance, clean off any hazardous
substances that may (due to working pro-
cesses) have accumulated on the appliance.
Avoid all skin contact with these substances.
If the skin comes into contact with hazardous
dusts, this can lead to severe dermatitis. If
dust is produced or swirled up during mainte-
nance, it can be inhaled.
NOTE
To ensure correct functioning and long-term
durability of the sander, pay attention to the
following points:
■ Sufficient and continuously intact oil lubrication
is highly important for optimum functioning.
■ Check the speed and vibration levels after each
use.
■ Check the idle speed regularly and after any
maintenance is performed:
use a rev counter and perform the measurement
without any clamped tools. The idle speed may
not be exceeded under any circumstances at a
residual pressure of 6.3 bar.
■ If the appliance is exhibiting excessive vibration
levels, the cause of the vibrations must be identi-
fied and repaired.
■ Use only the genuine replacement parts recom-
mended by the manufacturer, otherwise you
could put users at danger. In doubt, contact the
Service Centre.
■ Check the grinding disc
regularly for damage.
■ Clean the appliance with a soft, dry cloth only.
■ Never use sharp or scratchy cleaning agents
under any circumstances.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDEXS 150 B2 - IAN 110141 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDEXS 150 B2 - IAN 110141 in the language / languages: English, German, Dutch, French, Swedish, Finnish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info