786093
35
Zoom out
Zoom in
Previous page
1/200
Next page
35
GB IE
Wear gloves when handling the
blade.
Cleaning and general
maintenance work
Cleaning and maintenance work on
the underside of the appliance:
Place an underlay under the petrol
lawnmower.
1. Fold the upper handlebar (1) up
2. Release the quick release levers (5) and
fold up the upper bar (3).
3. Tilt the device back so that the spark
plug faces upwards.
Make sure that a second person
holds the device because there is a
danger of tipping backwards.
Do not tilt the device to the side or
forwards. Operating fl uids could
escape and the engine could be
damaged.
Always keep the device clean. Use a
brush or cloth for cleaning, but do not
use any aggressive cleaning agents or
solvents.
Do not use any water to clean the
engine, it could contaminate the fuel
system.
After mowing, remove any plant re-
mains using a piece of wood or plastic.
Clean the ventilation holes in particular
(7), the ejector opening and the blade
area. Do not use any hard or sharp
objects, as these could damage the de-
vice.
Check the device before each use for
obvious defects such as loose, worn or
damaged parts. Ensure that all nuts,
bolts and screws are fi rmly in place.
Check the covers and protective de-
vices (2, 7, 15, 19) for damage and
correct fi t. Replace these if necessary.
Replacing the air fi lter
Never run the device without an air
lter. Dust and dirt may otherwise
enter the engine and cause dam-
age.
Removing the air fi lter
1. Disconnect the spark plug connector
(11) (see “Spark plug maintenance”).
2. Open the air fi lter box (9).
3. Remove the air fi lter (10).
4. Clean the air fi lter (10) in a soap solu-
tion.
5. Allow the air fi lter (10) to dry. Put a
few drops of fresh engine oil into the
air fi lter.
6. Replace the faulty air fi lter with a new air
lter (see „Spare parts/Accessories“).
Inserting the air fi lter
1. Insert the air fi lter (10) into the air fi lter
box (9).
2. Close the air fi lter box (9) back up.
Spark plug maintenance
Worn spark plugs, or a spark plug
gap that is too large, will lead to a
reduction in engine power.
1. Remove the spark plug connector (11)
by pulling and turning the spark plug
(12).
2. Unscrew the spark plug (11) counter-
clockwise with the enclosed spark
plug wrench (27).
3. Check the spark plug gap with the help
of a feeler gauge (available from spe-
cialised dealers). The spark plug gap
must be 0.7-0.8 mm.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PBM 42 A1 - IAN 373349 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PBM 42 A1 - IAN 373349 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info