Manual Parkside IAN 307044 PKS 2200 A1 (page 43 of 196) (English, German, Dutch, French, Polish)

749294

Zoom out

Zoom in

1/196

IEGB

14 Switch-on block

The switch-on block must be

released for switching on the

device.

18 Chain catcher

Decreases the danger of injuries if

the chain breaks or if it comes off.

Assembly

Always wear protective

gloves when working with

the chainsaw and employ

only original parts. Pull out

the power plug before doing

any work on the chainsaw

itself -– injury hazard!

Before putting the electric chain saw into

operation, you must:

- install the blade, saw chain and chain

cover where necessary,

- adjust the saw chain tension,

- pour in chain oil,

- check the function of the chain brake

and the automatic oil pump.

Mounting the saw chain and

blade

 

2. Turn the fastening bolt (14) anti-

clockwise ( ) to remove

the sprocket chain wheel cover-

ing (8).

3. Spread the chain (5) out into a

loop with the cutting edges run-

ning clockwise .

4. Slide the saw chain (5) into the

bar guide groove. To mount the

guide bar (4), raise it to an angle

of approx. 45 degrees. This will

make it easier to replace the saw

chain (5) onto the sprocket (24).

5. Place the chain bar (4) and saw

chain (5) on the bar bolts (23).

When the nose on the right be-

low the bar bolt (23) sits in the

round recess on the blade, the

blade is placed correctly. It is nor-

mal for the saw chain (5) to sag.

It is normal that the saw chain (5)

is slack.

6. Pre-tension the saw chain (5) by

turning the screw for the chain

quick-tensioning system (9) in

clockwise direction.

7. Position the sprocket chain wheel

covering (8). First place the tab

(25) on the cover into the corre-

sponding notch on the plate (8).

Tighten the fastening bolt (7).

Note that the saw can re-oil.

Please note that the saw re-oils after use

and oil may leak out if it is stored on its

side or on the head. This is a normal

process due to the necessary ventilation

opening on the upper edge of the tank and

does not constitute a reason for complaint.

As each saw is checked during production

and tested with oil, a small residue may

be in the tank despite draining, which may

slightly dirty the housing with oil in transit.

Please clean the housing with a cloth.

Prior to changing the chain, the nut of the

guide rail must be cleaned of dirt because

dirt deposits available can cause the chain

to break out of the rail. The deposits can

also absorb the chain oil. So the conse-

quence would be that the chain oil would

not or only a small part of it would reach

the underside of the rail and the lubrication

would be reduced.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 307044 PKS 2200 A1 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 307044 PKS 2200 A1 Manual

Product: