Manual Parkside IAN 304520 PTBM 500 E5 (page 30 of 144) (English, German, Dutch, Danish, French, Polish)

748958

Zoom out

Zoom in

1/144

GB IE

place the battery in direct sunlight and

do not use or store it in motor vehicles

in hot weather.

• Store used batteries in the original pa-

ckaging and keep them away from me-

tal objects. Do not mix (up) unpacked

batteries! Otherwise this may cause the

battery to short-circuit, resulting in da-



• Remove batteries from the device if this

is not going to be used for a prolonged

period, unless it is to be used in emer-

gencies!

• NEVER touch batteries which have

leaked without appropriate protection.

If the leaked liquid comes into contact

with the skin, you should rinse off this

area of the skin immediately under run-

ning water. Make sure at all events that

your eyes and mouth do not come into

contact with the liquid. If they do, seek

medical advice immediately.

• Clean the battery contacts and the

equivalent contacts in the device before

inserting the batteries.

Assembly

The bench drill is supplied disassembled.

Clean the column tube (14), baseplate (17),

drilling bench (20), vice (23) and the drill

chuck (4) beforehand, with a dry cloth.

1. Place the column tube (14) on the ba-

seplate (17). Bolt the column tube (14)

to the baseplate (17) with the three as-

sembly srews (16) supplied. Tighten the

assembly srews (16) moderately tight

so that the threads in the baseplate (17)

do not strip.

2. Place the drilling bench (20) on the co-

lumn tube (14). Push the drilling bench

(20) into a lower position. Use the



bench (20) in a lower position.

3. Place the vice (23) on the drilling



the drilling bench (20) by means

of the enclosed assembly screws

(22) together with the washer

and the lock washer in the order

as shown.

4. Place the motor unit (13) on

the column tube (14). Secure

the motor unit (13) with the two

clamping screws (27) on the

side using the enclosed Allen key

(25).

5. Bolt the three drill lifting arms

into the spindle guide (9). Tigh-

ten the three hole lifting arms

with a spanner (AF 6 mm).

6. Release the clamping screw from

the depth stop (8).

7. Mount the laser on the motor unit



Make sure that the battery com-

partment (36) is on the side of

the hand spindle guide (9).

8. Put the safety device (6) on the

upper part of the drill spindle

(7).

9. Secure the safety device (6) with

the clamping screw (28).

10. Fold the safety device (6) up-

wards. Insert the chuck (4) on

the taper of the drill spindle (7).

Push the drill chuck onto the drill

chuck tip with a few light taps.

Use a plastic hammer for this

purpose.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 304520 PTBM 500 E5 in the language / languages: English, German, Dutch, Danish, French, Polish as an attachment in your email.

The manual is 4,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 304520 PTBM 500 E5 Manual

Product: