748958

Parkside IAN 304520 PTBM 500 E5 Manual

32
Zoom out
Zoom in
Previous page
1/144
Next page
32
GB IE
Recommended speeds for
different drill sizes and materials:
[mm]
[mm]
[1/min]
< 3 < 4 2500
3
-
4 5 - 6 1600
5 7 - 8 1100
6 - 8 9 - 10 830
> 8 > 10 500
Checking the V-belts
1. Release the locking bolt (11) on the
gear cover (3).
2. Open the gear cover (3).
3. Check the tension of the V-belts (29).
4. The V-belts (29) are correctly tensioned
when they give way slightly when
pressed.
5. Check the V-belts (29) for tears, cuts or
other damage.
6. Close the gear cover (3). Fasten the
locking bolt (11) on the gear cover (3).
Tensioning the V-belts
1. Release the locking bolt (11) on the
gear cover (3).
2. Open the gear cover (3).
3. Release the retaining screw (12) on the
motor unit (13).
4. Using the lever (33), slide the motor
unit (13) backwards to tighten the V-
belts (29).
5. The V-belts (29) are correctly tensioned
when they give way slightly when
pressed.
6. Re-tighten the retaining screw (12) on
the motor unit (13).
7. Close the gear cover (3). Fasten the
locking bolt (12) on the gear cover (3).
Adjusting the Drilling Bench
1. Release the locking handle (15).
2. Push the drilling bench (20) to the desi-
red height.
3. Pivot the drilling bench (20) to the desi-
red position.
4. Fasten the drilling bench (20) again
with the locking handle (15).
5. You can also adjust the tilt angle of the
drilling bench (20). To do this, release
the retaining screw (19) (AF 19 mm)
under the drilling bench (20). Tilt the
drilling bench (20) as desired to the
right or left up to a max. of 45° and se-
cure the drilling bench (20) again with
the retaining screw (19).
Preselecting the Drilling Depth
1. Release the locking screw from the
depth stop (8).
2. Lower the drilling spindle (7) with the
mounted tool on to the workpiece.
3. Turn the scale until the red marking
arrow attached to the motor unit (13) is
pointing to the zero line of the scale.
4. Now turn the scale to the desired
drilling depth and tighten the locking
screw (8) again.
5. Turn the drilling spindle (7) back to its
starting position.
Changing the Bit
Remove the plug from the mains
socket before changing the bit. This
will prevent an accidental start-up.
1. Fold the safety device (6) up.
2. Release the retaining jaws of the drill
chuck (4) with the drill chuck key (26)

3. Remove the bit.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 304520 PTBM 500 E5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 304520 PTBM 500 E5 in the language / languages: English, German, Dutch, Danish, French, Polish as an attachment in your email.

The manual is 4,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info