746864

Parkside IAN 292181 PDSP 1000 C3 Manual

20
Zoom out
Zoom in
Previous page
1/64
Next page
GB/IE/NI
20
Using the air-driven
sandblasting gun
Prepare your workpiece for sandblasting.
Clean and degrease your workpiece.
NOTE
Dust and grease deposits
will significantly impair your results.
Carefully cover up or mask off anything that
should not be sandblasted.
The distance from the attachment to your
workpiece is critical for the end result. Keep
the distance as short as possible, to ensure that
the
14
collecting bag
4
can catch all of the
material.
The closer you get to your workpiece, the small-
er the blasting radius on the workpiece itself,
and vice versa.
To check results beforehand, you can perform a
test run on a piece of scrap material. This helps
you to identify the right distance/working
pressure and avoids excessive sandblasting of
your actual workpiece.
Switching on:
Set the rotary control
7
to “1” to open the air
check valve.
Move the air-driven sandblasting gun
1
to the
surface you will be working on.
Press the trigger lever
3
to start using the
air-driven sandblasting gun
1
.
Switching off:
Release the trigger lever
3
to switch off the
air-driven sandblasting gun
1
.
Set the rotary control
7
to “0” to close the air
check valve.
Disconnect the device from the compressed air
supply after completing work.
NOTE
Detach the hose from the
compressed air supply first, before you remove the
supply hose from the device.
This will prevent a situation where the supply hose
whips around uncontrollably.
Emptying the collecting bag
for sandblasting material
NOTE
Do not reuse excess
sandblasting material from the collecting bag
4
before it has been properly cleaned.
You can empty the excess sandblasting
material that has been collected in the
collecting bag
4
by opening the bag’s zip
fastener. Alternatively, you can use a screw-
driver to loosen the screw clamp
5
and then
remove the collecting bag
4
from the device.
Operation
292181 Druckluft-Sandstrahlpistole_content_LB8.indb 20 29.11.17 18:34
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 292181 PDSP 1000 C3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292181 PDSP 1000 C3 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info