Manual Parkside IAN 275671 PDSS 310 A2 (page 11 of 69) (English, German, Dutch, Danish, French)

745544

Zoom out

Zoom in

1/69

12 GB/IE

Commissioning / After initial use / Maintenance / Cleaning and Care Commissioning

Connecting

Note: only use connection hoses with a minimum

inside diameter of 9 mm.

First wrap a piece of Teﬂon tape (not included)

around the outer threads of the plug nipple

and the lubricator

(see ﬁg. B).

Now screw the plug nipple

into the thread

of the lubricator

(see Figure C).

You must use an open-end spanner to tighten

this connection with moderate force.

Now turn the combination of lubricator

and

plug nipple

into the connection thread

of the impact driver (see Fig. C).

Also retighten this connection with an open-end

spanner.

Now press the air hose onto the plug nipple

using a little force, until the hose locks in.

ATTENTION! Be sure the air hose

is ﬁrmly connected. A loose hose

whipping about out of control pre

sents

a major hazard. Also ensure the two screw

connections between lubricator

, coupling

and machine are securely seated.

Adjusting the compressed air

Note: this device is designed for an operating

pressure of up to 6.3 bar and a compressor with

the minimum air ﬂow speciﬁed in the technical spe-

ciﬁcations. When setting the air pressure, remember

the pressure drops by approx. 0.6 bar with a hose

length of 10 m and an inside diameter of 9 mm.

Only use ﬁltered, lubricated and regulated

compressed air.

Adjusting the torque

Set the torque control

to the correct torque

by pressing it toward the housing and turning it

until it locks at the desired setting.

Be sure the operating pressure of the compres-

sor is between 5 and 6.3 bar.

Note: the ideal pressure is 6.3 bar. The maximum

torque cannot be reached at a pressure of only 5

bar or with insuﬃcient air ﬂow.

Setting

1 (low, min.)

2 (normal)

3 (high)

4 (extra high,

max.)

Initial use

Activate the trigger

to start the equipment.

Release the trigger

to deactivate the equip-

ment.

Changing rotation

ATTENTION! The device must come to a

complete standstill before changing the direc-

tion of rotation.

ATTENTION! A machine rotating in an unex-

pected direction can be dangerous. Always

pay attention and use care.

Note: The impact driver clockwise / counter-

clockwise rotation. Use the reverse switch

to change the direction of the impact driver.

Push the bolt forward in the direction of the „F“

marking („Forward / Fasten“) for clockwise

operation. You can now e.g. tighten screws.

Push the bolt back towards the „R“ marking

(„Reverse / Release“) so it protrudes from the

back of the equipment to set to counter-clock-

wise mode. You can now e.g. loosen screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275671 PDSS 310 A2 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 275671 PDSS 310 A2 Manual

Product: