745341

Parkside IAN 273278 PTS 500 A1 Manual

12
Zoom out
Zoom in
Previous page
1/74
Next page
9
PTS 500 A1
GB
IE
e) Do not use a toothed or chain saw blade or
segmented diamond-coated disc with more
than 10 mm wide slits. Such accessory tools
cause a kickback or loss of control over the
power tool.
f) Avoid cutting disc jams or excessive contact
pressure. Do not make any excessively deep
cuts. Overloading the cutting disc increases the
stress and likelihood of tilting or jamming and
thus the possibility of kickback or breakage of
the grinding tool.
g) If the cutting disc jams or you stop working,
switch the tool off and hold it steady until the
disc has completely stopped turning. Never
attempt to pull a rotating cutting disc out of a
cut. This could lead to kickback. Identify and
remove the cause of the jam.
h) Do not switch the power tool back on as long
as it is in the workpiece. Allow the cutting disc
to reach its full speed before you carefully
continue the cut. Otherwise, the disc may jam,
jump out of the workpiece or cause kickback.
i) Support panels or large workpieces to
reduce the risk of the cutting disc jamming
and causing a kickback. Large workpieces can
bend under their own weight. The workpiece
must be deposited on both sides of the disc,
namely in the vicinity of the cutting disc and
also at the edge.
j) Be particularly careful when making "pocket
cuts" into existing walls or other obscured
areas. The protruding cutting disc may cut gas
or water pipes, electrical wiring or other objects
that can cause kickback.
Supplementary notes
Approved cutting disc designs:
Diamond-coated, disc diameter 85 mm, disc thick-
ness max. 1.8 mm
■ Always wear a dust mask!
■ Always wear ear protectors!
Original accessories/auxiliary
equipment
■ Only use the accessories and additional equip-
ment that are specified in the operating instruc-
tions and are compatible with the appliance.
Cutting saw blade (symbols)
Wear ear protectors!
Wear protective glasses!
Wear safety shoes!
Wear protective gloves!
Wear a dust mask!
Not approved for wet grinding!
Approved diameter of tools
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273278 PTS 500 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273278 PTS 500 A1 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info