745341
13
Zoom out
Zoom in
Previous page
1/74
Next page
10
PTS 500 A1
GB
IE
Safety instructions for grinding tools
a) General
Grinding tools are very fragile and likely to break
which is why great care must be taken when hand-
ling the grinding tools. Using damaged, incorrectly
clamped or incorrectly installed grinding discs is
dangerous and may cause serious injury.
b) Handling, transport and storage
Grinding tools are to be treated with care and
transported carefully. Grinding tools should be
stored in such a way that they are not exposed
to mechanical damage or harmful environmental
influences.
Avoid any risk of an electric shock.
Check the condition of the device, power cord
and power plug at regular intervals. Stop using
appliances where the aforementioned parts are
damaged. Never open the device. Damaged
appliances, power cords or power plugs cause
danger to life by electric shock. Have repairs
and replacement work done only by the Service
centre or a qualified electrician.
Do not operate the appliance if it is damp or in
a humid environment.
When working outdoors, connect the appliance
via a fault current circuit breaker with a max-
imum tripping current of 30mA. Use only an
extension cord approved for outdoor use.
NOTE
Always hold the power cord away from the
working area of the machine and run it to the
rear away from the machine.
Operation
Switching on and off
Switching on:
Pull the ON / OFF switch
back.
Switching off:
Release the ON/OFF switch
.
Releasing the plunge lock
Push the plunge lock forward and keep it
pressed.
Selecting the cutting depth
NOTE
We generally recommend setting the cutting
depth to approx. 2 mm more than the
thickness of the material. This ensures that you
achieve a clean cut.
Release the quick-release lever for setting the
cutting depth
, and set the desired cutting
depth on the dial
7a
and clamp the quick-re-
lease lever again.
Fitting the rip fence
Loosen the rip fence screw
11a
on the base
plate and insert the rip fence into the
rip fence slot . Tighten the screw
11a
again.
Handling the plunge saw
1. Place the machine on the material and switch
on, as described in the chapter "Switching on
and off".
2. If necessary, align the machine using the rip
fence
or by using a marked line.
3. Saw by applying moderate pressure.
Types of saw blades:
The types of saw blades supplied cover the most
common fields of application.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273278 PTS 500 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273278 PTS 500 A1 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info