502189
104
Zoom out
Zoom in
Previous page
1/112
Next page
FAQs | On-screen messages
104
Problem Causes / Actions
Other
The TV does not switch on
Press and hold the Standby On / Off switch on the remote control for about
1 second if Power LED is red.
Check the mains lead is plugged into the TV and the socket outlet.
The fuse in the mains plug may have blown. Replace it with one of an identical
rating. (p. 4)
The TV goes into Standby
mode
Auto power standby function is activated. (p. 12)
The TV enters Standby mode about 30 minutes after analogue broadcasting
ends.
The remote control does
not work or is intermittent
Are the batteries installed correctly? (p. 8)
Has the TV been switched on?
The batteries may be running low. Replace them.
Point the remote control directly at the TV’s remote control signal receiver
(within about 7 m and a 30 degree angle of the signal receiver).
Situate the TV away from sunshine or other sources of bright light not to shine
on the TV’s remote control signal receiver.
Parts of the TV become
hot
Even when the temperature of parts of the front, top and rear panels has risen,
these temperature rises do not cause any problems in terms of performance or
quality.
Permanently lit spots on
screen
Due to production process involved in this technology this may result in some
pixels which are permanently lit or unlit. This is not a malfunction.
Overcurrent error
message appears
The connected USB device might cause this error. Remove the device and turn
the TV off with Mains power On / Off switch, then turn it on again.
Check foreign objects are not inside the USB port.
An error message appears
Follow the message’s instructions.
If the problem persists, contact your local Panasonic dealer or the authorised
service centre.
On-screen messages
Message Meaning / Action
All tuning data will be erased
[Shipping Condition] will erase all tuning data. (p. 57)
Are you sure ?
Confirm correct operation.
Are you sure you want to
delete this timer ?
Press OK to delete timer.
Press RETURN to return.
Confirm correct operation.
Bad signal
The signal is weak. Check the aerial is plugged in properly. It may be
necessary to have an aerial installer check the signal and aerial alignment.
Reset channels. (p. 50)
Child Lock is active!
Press OK to enter PIN.
The selected channel is locked in Child Lock (p. 56). You must enter the PIN
number before the channel will be displayed.
External Recording Due to
Start
This message will appear 2 minutes before timer programming event for
external recording due to start.
Feature not available.
It is not possible to record from AV2 (COMPONENT) or HDMI. Connect the
recorder to the TV using a fully wired SCART cable for recording from the TV
tuner.
Confirm Q-Link or VIERA Link settings. (p. 84 - 87)
Feature not available.
Press OK to view how it works.
The selected feature on VIERA TOOLS is not available. Press the OK button to
view the demonstration to explain how to use it.
Found new software version
∗∗∗
.
Press OK to start update (may
take over 40 mins) or press
EXIT to ignore and you can
update when TV is in standby
There is a new software available.
Invalid operation - Please
check settings and
connections.
Check the Q-Link or VIERA Link connection and setting.
(p. 84 - 87)
104


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TX-P42ST50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TX-P42ST50 in the language / languages: English as an attachment in your email.

The manual is 4,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic TX-P42ST50

Panasonic TX-P42ST50 User Manual - English - 48 pages

Panasonic TX-P42ST50 User Manual - German - 112 pages

Panasonic TX-P42ST50 User Manual - Dutch - 48 pages

Panasonic TX-P42ST50 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info