536677
67
Zoom out
Zoom in
Previous page
1/115
Next page
Press 3) as to select the [PROJECTOR ID].
Select one from [ALL], and [1] to [6]. f
[ALL] Select when controlling projectors without specifying an ID number.
[1]-[6] Select when specifying an ID number to control individual projector.
Press the <ENTER> button to set it.4)
[PROJECTOR ID] is set. f
Note
The ID number can be set to [ALL], or from [1] to [6]. f
To specify an ID number for individual control, the ID number of a remote control must match the ID number of the projector. f
When the ID number is set to [ALL], the projector will operate regardless of the ID number specied during remote control or f
computer control.
If multiple projectors are set up side by side with ID set to [ALL], they cannot be controlled separately from the projectors
with other ID numbers.
Refer to “Setting the remote control ID numbers” ( f Æpage 23) for how to set the ID number on the remote control.
[INITIAL START UP]
Set the method of start up when the power cord plugged into the AC outlet.
Press 1) as to select [INITIAL START UP].
Press 2) qw to switch the item.
The items will switch each time you press the button. f
[LAST MEMORY] Starts in the condition that before disconnected the power cord or turn off the breaker.
[STANDBY] Starts up in the standby mode.
[ON] Starts the projection immediately.
[PROJECTION METHOD]
Set the projection method in accordance with the installation status of the projector.
Change the projection method if the screen display is upside down or inverted.
Press 1) as to select [PROJECTION METHOD].
Press 2) qw to switch the item.
The items will switch each time you press the button. f
[FRONT/DESK] When installing the projector on the desk, etc. in front of the screen.
[FRONT/CEILING] When installing the projector in front of the screen by using the Ceiling Mount Bracket for Projectors (optional).
[REAR/DESK] When installing the projector on the desk, etc. behind the screen (with a translucent screen).
[REAR/CEILING]
When installing the projector behind the screen (with a translucent screen) using the Ceiling Mount Bracket for
Projectors (optional).
[HIGH ALTITUDE MODE]
Change the setting according to the altitude in which you use the projector.
Press 1) as to select [HIGH ALTITUDE MODE].
Press 2) qw to switch the item.
The items will switch each time you press the button. f
[OFF] When using the projector in the elevation of below 1 400 m.
[HIGH1] When using the projector in the elevation of above 1 400 m and below 2 000 m.
[HIGH2] When using the projector in the elevation of above 2 000 m and below 2 700 m.
Note
It is set to [OFF] when using the projector in the elevation of below 1 400 m. It is set to [ f HIGH1] when using the projector in
the elevation of above 1 400 m and below 2 000 m. It is set to [HIGH2] when using the projector in the elevation of above
2 000 m and below 2 700 m. Failure to do so may shorten the life of the internal parts and result in malfunctions.
Do not set the projector in the elevation of 2 700 m or above, otherwise it may shorten the life of the internal parts and result f
in malfunctions.
When it is set to [ f HIGH1] or [HIGH2], the fan noise becomes louder and fan speed increases.
ENGLISH - 67
Chapter 4 Settings - [PROJECTOR SETUP] menu
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-VX410Z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-VX410Z in the language / languages: English as an attachment in your email.

The manual is 17,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info