457746
99
Zoom out
Zoom in
Previous page
1/120
Next page
Troubleshooting
VQT3C73
99
Messages on the unit’s display
Troubleshooting
The following messages or service numbers appear on the
unit’s display when something unusual is detected during
startup and use.
BD
(“” stands for a
number.)
The remote control and main unit are
using different codes. Change the code
on the remote control. (> 95)
CAM-UP
CAM is being updated. (> 97)
GUIDE
TV Guide data is being downloaded.
(> 29)
FINISH
The software (firmware) update is
complete. (> 97)
HARD ERR
If there is no change after turning the unit
on and off, consult the dealer where the
unit was purchased.
NoERAS
You cannot delete items on this disc.
The disc may be damaged. Use a new
disc.
NoREAD
The disc is dirty or badly scratched. The
unit cannot record, play, or edit. (> 9)
This message may appear when the
lens cleaner has finished cleaning.
Press [< OPEN/CLOSE] on the main
unit to eject the disc. (> 20)
NoWRIT
You cannot write to this disc.
The disc may be damaged. Use a new
disc.
PLEASE
WAIT
Displayed when the unit is started and
turned off.
There was a power failure or the AC
plug was disconnected while the unit
was on. The unit is carrying out its
recovery process. This process
restores the unit to normal operation.
The unit is not broken. Wait until the
message disappears.
PROG FULL
There are already 64 timer programmes.
Delete unnecessary timer programmes.
(> 38)
REMOVE
The USB device is drawing too much
power. Remove the USB device.
START
Update of the software (firmware) is
started.
You cannot operate the unit until the
update is complete. (> 97)
SW-DL
Software (firmware) is downloading.
Download will stop when the unit is
turned on, or the timer recording starts.
(> 97)
UNSUPPORT
You have inserted a disc the unit cannot
play or record on. (> 6)
You tried to operate with a non-
compatible USB memory.
UPD /
(“” stands for a
number.)
The software (firmware) is being
updated.
You cannot operate the unit until the
update is complete. (> 97)
U59
The unit is hot.
The unit switches to standby for safety
reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation
when installing the unit. Do not block the
cooling fan on the rear of the unit.
U61
(When a disc is not inserted) Displays
when a malfunction has occurred. This is
displayed when the unit is in the recovery
process to return to normal operation.
Once the display clears you can use the
unit again.
If it remains displayed, consult the dealer
where the unit was purchased.
U76
HDMI cannot be output because it is
connected to a model that does not
support copyright protection.
U77
Due to the current disc not having
authorised copyright information, video
output is not performed.
U88
(When a disc is inserted) Displays when
there was something unusual detected
with the disc while recording, playback or
copy. This is displayed when the unit is in
the recovery process to return to normal
operation. Once the display clears you
can use the unit again.
If it remains displayed, consult the dealer
where the unit was purchased.
U99
The unit fails to operate properly. Press
[Í/I] on the main unit to switch the unit to
standby mode. Now press [Í/I] on the
main unit again to turn the unit on.
H or F
(“” stands for a
number.)
There is something unusual. (The
service number displayed after H and F
depends on the unit’s condition.)
Check the unit using the
troubleshooting guide. (> 100) If the
service number does not disappear, do
the following.
1. Disconnect the plug from the
household mains socket, wait a few
seconds, then reconnect it.
2. Press [Í/I] to turn the power on. (The
unit may be fixed.)
If the service number does not disappear
despite after doing the above, request
service from the dealer. Inform the dealer
of the service number when requesting
service.
XHOLD
The HOLD function is activated.
Press and hold [OK] and [RETURN ] at
the same time until “X HOLD”
disappears. (> 20)
DMRBST800700701EG_eng.book 99 ページ 2011年4月26日 火曜日 午後5時27分
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic DMR-BST700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic DMR-BST700 in the language / languages: English as an attachment in your email.

The manual is 5,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic DMR-BST700

Panasonic DMR-BST700 User Manual - German - 120 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info