668497
9
Zoom out
Zoom in
Previous page
1/51
Next page
9
Sensitive edges safety inputs left side
If one of these safety devices are controlled, the lift can not move in the left direction.
It is still possible for the lift to move in the right direction.
Control input connected to connector-name
Endswitch left (NC) X3a-
3,4 Endswitch
Safety drive unit left (NC) X4-
3,4 Drive
Safety footrest left (NC) X5-
3,4 Foot
Safety chairframe left (NOTE) (NC) X6-
3,4 Frame (NOTE)
(NOTE) Not used in the Otolift ‘ONE’.
In this lift there is no safety-device chairframe.
The input is on the PCB to be able to use this PCB in type 86+ applications. (future backwards
compatibility).
In this lift this input is connected via a jumper.
3.1.4 Other inputs
Battery supply Battery connection for 2 x 12V batteries in series.
Batteries are fused through a cable between the 2 batteries.
Transformer 24 DC/35VA is used for powering the charge-circuitry on main PCB
(Through charging-points connected to X10-
1,2 (charge))
Rotation monitor unit This switch is triggered by a moving part, which is mounted on the
overspeed governor mechanism, which drives over the rail.
This contact is checked for an alternating value while moving.
Rotation monitor unit (rmu) is connected to X9a.
Dipswitches For setting and function see chapter 5.1 and 5.2
Service box Multipurpose tool for:
- Programming the chairlift, with self chosen programmable speeds.
- Moving the lift in combination with bypass-connectors, when a
defect is active.
- Read out error-log.
The service box should be connected to x13 (service)
Bypass-connector Use for interconnection of safety-contacts.
Can only be used in combination with service box.
The bypass-connector should be connected to x15 (bypass) and can be
activated by controlling the ‘Hold to run’ at the service box.
Dual Safety line A B input The bypass connector is normally used as the interconnection of the
safety-lines between the main board and the level board.
You need to take out this connection first to be able to work with the
bypass.
CAN-bus Communication between Main, Level and sensor control board.
Connection through 8 pole header. (x16).
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Otolift One at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Otolift One in the language / languages: English as an attachment in your email.

The manual is 4,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info