589363
6
Zoom out
Zoom in
Previous page
1/10
Next page
EN
5
CHECK REMOTE AND INDOOR
TEMPERATURES
The indoor temperature is shown on the 3rd line of
the display.
To check the temperature at a remote sensors location,
you need to select its channel. Press CHANNEL to
go from one channel to another. The kinetic wave
display on the channel number indicates the reception
of that particular channel is in good order.
If no readings are received from one particular channel
for more than two minutes, blanks “
” will be
displayed until further readings are successfully
searched. Check that the remote unit is sound and
secure. You can wait for a little while or press
CHANNEL and MEMORY simultaneously to enforce
an immediate search. No reading will be shown if no
remote unit is assigned to a selected channel.
The temperature trend indicator on the screen shows
the trend of samplings collected at a particular remote
site. Three trends, rising, steady, and falling will be
shown.
Rising Steady Falling
Arrow
indicator
Temperature
Trend
If the temperature goes above or below the
temperature measuring range of the main unit or the
remote unit (stated in specification), the display will
show “HHH” or “LLL”.
READ THE KINETIC WAVE DISPLAY
The kinetic wave display shows the signal receiving
status of the main unit. There are three possible forms:
The unit is in searching
mode.
Temperature readings are
securely registered.
No signals.
MAXIMUM AND MINIMUM TEMPERATURES
The maximum and minimum recorded indoor
temperatures and those of each channel will be
automatically stored in memory. To display them:
1. Select the channel to be checked.
2. Press MEMORY once to display the maximum
temperature and again the minimum temperature.
The respective indicators, MAX or MIN will be
displayed.
To clear the memory, press and hold MEMORY for
two seconds. The maximum and minimum
temperatures will be erased. If you press MEMORY
now, the maximum and minimum temperatures will
have the same values as the current ones until new
readings are recorded.
DISCONNECTED SIGNALS
If without obvious reason the display for a particular
channel goes blank, press CHANNEL and MEMORY
to enforce an immediate search. If that fails, check:
1. The remote unit of that channel is still in place.
2. The batteries of both the remote unit and main
unit. Replace as necessary.
3. The transmission is within range and path is clear
of obstacles and interference. Shorten the
distance when necessary.
For best results, use lithium ion batteries in the remote
sensing unit if the outdoor temperature falls below
41 °F (-5 °C), other battery types will not function at
such low temperatures.
TRANSMISSION COLLISION
Signals from other household devices, such as door
bells, home security systems and entry controls, may
interfere with those of this product and cause
temporarily reception failure. This is normal and does
not affect the general performance of the product. The
transmission and reception of temperature readings
will resume once the interference recedes.
SWITCHING BETWEEN °C AND °F
The unit of temperature display is selected on the °C/°F
slide switch. Select °C for Centigrade or °F for Fahrenheit.
The remote temperature display shown on the
main unit is dominated by the selection on the °C/°F
slide switch of the main unit. Whatever the display units
of the remote sensors are, they will be automatically
converted to the chosen one of the main unit.
WEATHER FORECAST FUNCTION
Your BAR888 detects barometric pressure changes
and the LCD displays the illustrated weather symbols
which indicates the weather forecast for 12 to 24 hours
ahead, for an area with a radius of about 30-50 km.
NOTE
Indicator
displays on
the unit
Forecast Sunny Slightly
Cloudy
Cloudy
Rainy
BAR888 Eng R5 R 6/8/04, 10:44 AM5
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific BAR888 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific BAR888 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oregon Scientific BAR888

Oregon Scientific BAR888 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info