47327
12
Zoom out
Zoom in
Previous page
1/25
Next page
COMMAND CENTER
11
4-2 Basic > Security
The Administrator (Admin) account is the master access account. It controls access to
the printer and networking configuration from all setup and management utilities
including the HTML web pages.
Notes
The factory default for COMMAND CENTER is no password. Setting the Admin
password is highly recommended to prevent unauthorized changes to the printer and
networking configuration.
The password can be to up to 30 characters long.
We recommend that you record your password so that you do not forget it. If the
Admin password is forgotten, a reset to factory defaults with a jumper setting is
required to eliminate the password.
To Change the Password:
1
Enter the Old Password.
2
Enter the password you want to set in
New Password.
3
Enter the same password in Confirm New Password.
4
Click Submit at the button of the page.
4-3 Basic > Network
This page allows you to make the settings that are required for network printing and
sending e-mail. For more information, refer to Advanced > Protocols: TCP/IP:
General on page 15.
Note
Always restart this machine after you have completed these settings in order to properly
register the content of those settings in the machine. Refer to Basic > Reset on
page 12.
Item Description
Host Name Specifies a name for the printing system network component. This name is
also used as the NetBEUI Printer Name and the SNMP sysName object.
IP Address Assigns the Internet Protocol address on the printing system network
component. Format of the IP Address is four-byte (32-bit) numbers
separated by dots, e.g.
192.168.110.171.
Subnet Mask Specifies the subnet mask configured on the printing system network
component. If the printing system does not automatically assign a usable
default value and the first number in the IP address above is from 192 to
254, then use 255.255.255.0 as the subnet mask.
Default Gateway The IP address of the gateway router for the local network.
DHCP/BOOTP Identifies how the machine obtains its IP configuration:
DHCP/BOOTP: automatic configuration via a BOOTP server or a DHCP
server.
Rendezvous This product supports Apple Rendezvous. Printers can be added from the
Printer Center in Mac OS X. To allow printing, the printer should support
KPDL. This setting enables (On) or disables (Off) Rendezvous.
Rendezvous Name Specifies the name to use for Rendezvous.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP1016 Operation Guide Command Center at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP1016 Operation Guide Command Center in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info