47327
24
Zoom out
Zoom in
Previous page
1/25
Next page
COMMAND CENTER
23
7 Troubleshooting
If trouble occurs with COMMAND CENTER, carry out the applicable checkpoints and
procedures indicated on the following pages. If the trouble persists, contact your service
representative or authorized service center.
Trouble Check point Procedure Reference
Page
I can’t access COMMAND
CENTER.
Is the power turned on to this
machine?
Turn the power on to this machine,
wait until it is a ready state and try
to access COMMAND CENTER.
-
Is the network cable properly
connected?
Connect the network cable
properly.
-
Are the network settings that are
made in this machine correct?
Perform the network settings from
the operation panel. Contact your
network administrator for
information on the appropriate
settings.
-
Is the IP address for this
machine entered correctly?
Enter the correct IP address.
Check with your network
administrator to make sure the
correct IP address has been
designated for this machine.
-
Are the LAN settings that are
made in your browser
application correct?
Check the settings made in your
browser application. For details,
refer to the Help function, etc. in
your browser application.
-
Has the administrator set up an
IP Filter function?
Access COMMAND CENTER
from an approved IP address.
15
The SNMP Read Community
settings function as passwords
to control read and write access
to the device via SNMP.
Access COMMAND CENTER
from an approved Read
Community.
18
Does the version of your
browser application support
operation using COMMAND
CENTER?
Use a browser application that
supports operation using
COMMAND CENTER.
3
Characters do not display
properly in COMMAND
CENTER.
Does the version of your
browser application support
operation using COMMAND
CENTER?
Use a browser application that
supports operation using
COMMAND CENTER.
3
I can’t access the Basic,
Printer, and Advanced pages.
Has the administrator set a
password?
Enter the appropriate password. -
I can’t perform settings. Is the printer currently in
operation?
Settings are not possible while the
machine is currently printing. Wait
until the operation has been
completed.
-
The settings I made are not
registered.
Did you click on the Submit
button after making the
settings?
After you make the desired
settings, click on the Submit
button and move to another page
or close COMMAND CENTER
window.
10
Did you click on the Restart
button after making the network
settings? Network settings are
not registered until the machine
is restarted.
Restart this machine. All settings
will be registered.
12
The administrator has forgotten
the Admin password.
- If the Admin password is
forgotten, reset to factory defaults.
12
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP1016 Operation Guide Command Center at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP1016 Operation Guide Command Center in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info