Manual Novoferm NovoPort 2016 (page 18 of 134) (All languages)

709124

Zoom out

Zoom in

1/134

Further hand transmitters (up to a maximum of 30)

can be programmed.

Menu stage 2: Programming the light

function for the hand transmitter

Press key briefly and figure 1 will be displayed.

Press key once again and figure 2 will be

displayed.

Press the second button at the transmitter with which

the 4-min light is to be switched on. As soon as the

code has been read in, the red point display (a) will

flash 5 times to acknowledge the entry. Figure 0 will

be displayed. Menu finished.

Deleating all the hand transmitters programmed

for the operator:

Plug in the operator‘s main plug while pressing

button .

Menu stage 3: Setting / adjusting the top end-

of-travel position

Keep button pressed for 3 seconds. Number 3

appears in the display 17a.

Wait a short while until the 3 starts flashing.

Press button and make sure that the door travels in

the OPEN direction.

If the door closes in the wrong direction, after

having pressed , keep button pressed for

another 3 seconds. “3” flashes briefly. The

travelling direction is altered.

Now travel by pressing button into the desired door

end position OPEN 17b.

By pressing button , the position can be corrected

into direction CLOSE.

Once the desired OPEN end-of-travel position has

been reached, press button . The operator stores

the OPEN end-of-travel position and “4” appears in

the display.

Menu stage 4: Setting / adjusting the bottom

end-of-travel position

Wait a short while until “4” starts flashing.

Press button . The operator causes the door to

travel in the CLOSE direction as long as the button is

pressed. The position can be altered to the OPEN

direction via button . Once the desired CLOSE end-

of-travel position has been reached, press button .

The operator stores the CLOSE end-of-travel

position and “0” appears in the display.

Force-learning cycle

We recommend setting the suitable door type in

menu stage 8 prior to the force-learning cycle.

During this opening and closing cycle, the

operator learns the force required to open and close

the door. The cyclesA force limit does not apply!

must not be interrupted. During these cycles must

not be interrupted. During these cycles “0” appears

in the display.

- Press button . The operator causes the door to

open until the top end-of-travel position has been

reached.

- Now press button again. The operator causes

the door to close until the bottom end-of-travel

position has been reached.

- After approx. 2 seconds, “0”disappears.

Checking the force limit device

- Position the force-measuring device

(dynamometer) in the closing area.

(If a measuring device is not available, use, for

example, the operator’s cardboard box)

- Start the door from the OPEN end-of-travel

position.

- The door travels towards the obstruction, stops

and re-opens.

If the door springs were altered, the force-learning

operation must then be repeated:

Call up menu stage 5 and keep button depressed

for 3 seconds. A "0" is displayed. Then carry out

force-learning operations as explained under point

19.

• Special settings

In order to access the menus for the special settings,

keep key pressed for 3 sec until figure 3 is

displayed. Press key to by-pass menu step 3.

Now keep key pressed for 3 sec until figure 5 is

displayed. Press key to by-pass menu steps.

Menu stage 5: The opening force limit

If you have previously quit the setting menu, press

button for 3 seconds until “3” appears. Then press

button twice until “5” appears.

After approx. 2 seconds, the display flashes showing

the set value of the opening force limit. The force limit

setting can be increased for decreased via buttons

and .After setting the value, press button .

The display shows “6”.

Menu stage 6: The closing force limit

After approx. 2 seconds, the display starts flashing,

and the set value for the closing force limit is

displayed.

The force limit setting can be increased or decreased

via buttons and .

After setting the value, press button . “0” appears

in the display.

Finally, check the force settings, and, if necessary,

repeat the setting procedure.

The maximum force at the main closing edge must

not exceed 150 N!

Menu stage 7: Light phases

Press button . “7” appears in the display.

Menu Light Warning 24V

value phase phase

0 60 s - 60 s

1 120 s - 120 s

2 240 s - 240 s

3 0 s - 0 s

4 0 s 3 s 0 s

5 60 s 3 s 0 s

6 120 s 3 s 0 s

7 60 s 0 s TAM

8 120 s 0 s TAM

9 240 s 0 s TAM

When the advance warning time is set, the light and

24 V will be switched on before the drive starts

running.The factory setting is 1.

TAM: OPEN signal, when the door is not closed 24V

are available for signalling.

Menu stage 8: Door fitting

Press button . “8” appears in the display.

Menu Start Stop Start Stop

value open open closed closed

0 0 0 0 0

1 15 0 15 0

2 0 15 0 40

3 15 15 15 35

4 25 30 25 40

5 15 15 15 55

6 15 15 15 15

7 35 35 65 45

8 55 15 15 100

9 only soft run

These values correspond to the “soft” runs

measured in cm at the carriage.

Menu stage 9: special functions

Push button .“9” is displayed.

Menu Operating mode

value

0 Normal operation

1 Normal operation with ventilation

position

The ventilation position can be initiated by

pressing the second push button on the

hand transmitter or via the signal 112

internal push button (accessory).

2 Partial opening of side sectional doors

Partial opening of approx. 1m can be

initiated by pressing the second push

button on the hand transmitter or via the

signal 112 internal push button

(accessory).

Advice: The 2nd push button of the transmitter has

to be teached-in again after changing the operation

mode.

Internal impulse generators

The cover on the control unit is used as an impulse

generator for opening and closing from inside the

garage. Briefly press the cover and the operator

starts up .

Disengagement

The operator is equipped with a quick release. By

pulling the pull cord with knob , the operator can22a

be permanently disengaged from the door . “8” is22b

displayed.

The motor head can be re-engaged at any point

between the two limit switch actuators. To lock in

place, press down lever .22c

Installation on LH side of door

If favoured by the structural conditions on site, the

operator can also be installed on the left-hand side

ck on the other side .23c

23a. Loosen bolts on motor head with wrenches (SW

10 and 17mm) and screw them back on the23b

other side .23c

Low-mounted control unit

If the control unit cannot be positioned directly

underneath the track , the coiled cable can then24a

be routed to the motor head using the supplied

second cable clamp and the punched tape . The24b

extendible part of the coiled cable may be stretched

by a maximum of factor 3 and the permanently laid

part by a maximum of factor 7.

If the coiled cable is not long enough, the extension

set (accessory) should be used.

Connection for wicket door contact

The option of connecting the wicket door contact

to drive unit is an advantage.

- Remove housing .25a

- On the white plastic component, break out the

side wall towards the door .25b

- Route cable from wicket door contact over the

lifting arm and fasten with cable binder .25c

- Remove jumper from terminal block and25d

insert cable .25e

- Place housing back on again and screw down

.25f

Check: Open wicket door, "8" is displayed.

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

door open once by remote control after than stop with function Submitted on 28-6-2023 at 10:56
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm NovoPort 2016 in the language / languages: All languages as an attachment in your email.

The manual is 9,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm NovoPort 2016 Manual

Product: