709124
20
Zoom out
Zoom in
Previous page
1/134
Next page
Trouble-shooting Guide
Important note: when working on the operator, always pull out the mains plug beforehand!!!
Malfunction
Door does not open / close fully.
After closing, the door opens again slightly.
Door fails to move although the motor is
running.
Door does not respond on impulse from the
hand transmitter - but does respond to push-
buttons or other impulse generators.
Door does not respond to impulse from hand
transmitter nor to other impulse generators.
Insufficient range of hand transmitter.
Toothed belt or operator noisy.
Possible causes
Door mechanics have altered.
Door does not open / close fully.
Travel limit is incorrectly set.
Door blocks shortly before reaching the closed
position.
Travel limit is incorrectly set.
Operator is not engaged.
Battery in the hand transmitter is flat.
Aerial not available or not fitted.
No hand transmitter programmed.
See diagnostic display.
Battery in the hand transmitter is flat.
Aerial not available or not fitted.
On-site screening of the receiving signal.
Toothed belt dirty.
Tension of toothed belt too high.
Remedy
Have the door checked.
Set the forces (menu stages 5 and 6).
Reset travel limit .
Remove the obstruction.
Reset closed travel limit .
Re-engage the operator 22c.
Replace battery in the hand transmitter.
Plug in / align aerial.
Programme the hand transmitter ( menu
stage 1).
See diagnostic display.
Replace battery in the hand transmitter.
Plug in / align aerial.
Connect external aerial (accessories).
Clean toothed belt.
Spray with silicone.
Detension the toothed belt.
18
18
15
GB
Diagnostic display
During operation, the display provides diagnostic information on any possible faults / malfunctions
Number State Diagnosis / Remedy
_______________________________________________________________________________________________________________________
Operator starts up and 0goes out. Operator receives a start impulse at the START input or via a receiver,
normal operation.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Top end-of-travel position Open has been reached.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Bottom end-of-travel position Closed has been reached.
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Gate end position has not been reached.
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
0 displayed during the next opening and closing cycle Operator is carrying out a learning cycle for the force limit.
Caution:and then goes out. During these travel cycles the force is not monitored!
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
0 continues to be displayed. Force-learning cycle not completed. Must be repeated.
Too much pressure in the gate's end-of-travel positions. Gate setting required.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Door neither opens nor closes. STOP A connection is interrupted.
External safety device has been activated (e.g. wicket door).
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Door no longer closes. STOP B connection is interrupted.
External safety device has been activated (e.g. photocell).
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Gate setting und learning cycle not correctly finalized. Repeat gate setting in menus 3 & 4 and complete force-learning cycle
subsequently.
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Permanent impulse signal at the start input. Door no longer accepts a start impulse. External impulse generator emits a
permanent impulse signal (e.g. button is jammed)
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
An error ocurred in setting the operator. Travel path too long.
Repeat setting procedure (menu stages 3 and 4).
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Closing edge OSE has been activated. Check closing edge, spiral cable and optics.
Fault during learning cycle. Repeat position learning cycle. (menu stages 3 and 4)
Reduce force when approaching the end-of-travel positions.
Emergency release has been activated Operator is released, lock the coupling again .22c
or wicked door contact has been activated. Check wicket door contact.
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Door neither opens nor closes. Fault during self-test. Disconnect power supply.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Motor has come to a standstil. Motor does not rotate. Call in a specialist company.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Vacation lock activated, gate does not open. Slide switch at SafeControl / Signal 112 confirmed. Reset required.
Deleting radio codes
Press oval key. Keep key pressed while inserting power plug.
All radio codes stored in the hand-held transmitter are now deleted.
Restoring factory setting
Press Open and Close keys at the same time. Keep keys pressed for approx. 3 sec while inserting
power plug.
The factory setting has been restored.
20


Need help? Post your question in this forum.

Forumrules
1

Forum

novoferm-novoport-2016

Reset search

  • door open once by remote control after than stop with function Submitted on 28-6-2023 at 10:56

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm NovoPort 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm NovoPort 2016 in the language / languages: All languages as an attachment in your email.

The manual is 9,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info