787650
17
Zoom out
Zoom in
Previous page
1/31
Next page
USER MANUAL
ENGLISH
14
CAUTION!
Rotate the speed adjusting knob (41 as Figure 2) to the minimum speed before depressing
accelerate pedal (26 as Figure 1) to avoid the machine running too quickly when it is started.
Make sure the brush/pad is installed correctly before machine operating.
SQUEEGEE INSTALLATION AND ADJUSTMENT
1. Turn the ignition key (24 as Figure 1) to “I”, press One-Start button (38 as Figure 2), the squeegee (12 as Figure 1)
is lowered down to the floor automatically.
2. Unscrew two of adjusting knobs (21 as Figure 1) on the squeegee, then install the squeegee to the squeegee
bracket and tighten the adjusting knobs. After that, connect the vacuum hose (20 as Figure 1) to the squeegee to
complete the squeegee installation.
3. Adjust the squeegee by squeegee adjusting handle (A, Figure 9).
a) If there is gap between the ground and middle section of rear
squeegee blade (B), adjust the knob (A) in counterclockwise
direction (F) until all section of rear blade good touches with
the ground, the front blade touch the ground slightly.
b) If there is gap between the ground and both end section of
rear squeegee blade (C and D), adjust the knob (A) in
clockwise direction (E) until all section of rear squeegee blade
good touch with the ground, the front blade touch the ground
slightly.
SOLUTION TANK FILLING
NOTE
If the machine is equipped with Chemical
Mixing System (optional) the tank must
be filled with clean water, otherwise the
tank can be filled with solution.
1.
2.
Turn over the seat (A, Figure 10).
(For machines without Chemical Mixing System)
Use the front filler neck (B Figure 10) and the rear
filler neck (C Figure 10) to fill the tank (D Figure 10)
with a solution suitable for the work to be performed.
Refill to the reference mark “F” of the level check
hose (C Figure 10). Always follow the dilution in-
structions on the label of the chemical product used
to prepare the solution. The solution temperature
must not exceed + 104°F (+40°C).
E
A
C
F
BD
G
F
E
D
C
B
A
H
I
Figure 10
Figure 9
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk SC3500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk SC3500 in the language / languages: English as an attachment in your email.

The manual is 8.24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info