787650
30
Zoom out
Zoom in
Previous page
1/31
Next page
USER MANUAL
ENGLISH
27
Machine material composition and recyclability
Type Recyclable percentage Weight%
Aluminium 100 % 2%
Electric motors - various 29% 32%
Ferrous materials 100 % 14%
Wiring harness 80% 3%
Liquids 100 % 0%
Plastic - non-recyclable material 0% 1%
Plastic - recyclable material 100 % 6%
Polyethylene 92% 40%
Rubber 20% 2%
NOTE
Machine with battery charger installed, cannot operate if the charger is not on board. In case of
battery charger malfunction, contact an authorized Service Center. For further information
refer to the Service Manual, available at any Service Center.
SCRAPPING
Scrap the machine by the qualified waste treatment institution.
Before the machine is scrapped, please take away and segregate below subassembly that relevant laws and
regulations request must be disposed in appropriate way.
ˉBattery
ˉBrush/Pad-holder
ˉPlastic hose and plastic parts
ˉElectrical and electronic components (*)
(*) Please contact our service center to destroy any of electrical and electronic components.
2.3 ¤¤ ¤¤¤ MAIN FAULT * 1. Main contactor welded or stuck open.
2. Main contactor driver fault.
2.4 ¤¤ ¤¤¤¤ MAIN ON FAULT 1. Main contactor driver failed closed.
3.1 ¤¤¤ ¤ WIRING FAULT * 1. Misadjusted throttle.
2. Broken throttle pot or throttle mechanism.
3.2 ¤¤¤ ¤¤ BRAKE ON FAULT 1. Electromagnetic brake driver shorted.
2. Electromagnetic brake coil open.
3.3 ¤¤¤ ¤¤¤ PRECHARGE FAULT *
1. Brake driver shorted.
2. Precharge circuit damaged.
3. MOSFET failure.
3.4 ¤¤¤ ¤¤¤¤ BRAKE OFF FAULT 1. Electromagnetic brake driver open.
2. Electromagnetic brake coil shorted.
3.5 ¤¤¤ ¤¤¤¤¤ HPD FAULT
1. Improper sequence of throttle and KSI, push, or
inhibit inputs.
2. Misadjusted throttle pot.
4.1 ¤¤¤¤ ¤ CURRENT SENSE FAULT * 1. Short in motor or in motor wiring.
2. Controller failure.
4.2 ¤¤¤¤ ¤¤ HARDWARE FAILSAFE *
1. Motor voltage does not correspond to throttle
request.
2. Short in motor or in motor wiring.
3. Controller failure.
4.3 ¤¤¤¤ ¤¤¤ EEPROM CHECKSUM FAULT 1. EEPROM failure or fault.
4.4 ¤¤¤¤ ¤¤¤¤ POWER SECTION FAULT*
*= Must cycle keyswitch to clear.
= Must use programmer to clear, as follows: select Program menu, alter data value of any parameter, cycle
keyswitch.
1. EEPROM failure or fault.
2.Short in motor or in motor wiring
3. Controler failure.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk SC3500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk SC3500 in the language / languages: English as an attachment in your email.

The manual is 8.24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info