512550

Navman Depth 2100 Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
5
DEPTH 2100 Installation and Operation Manual
NAVMAN
Keel/Surface Offset
An offset may be automatically added to or subtracted
from the depth reading to compensate for the location
of the transducer. This allows the instrument to
indicate the water depth relative to the bottom of the
keel or the surface of the water.
To set the keel/surface offset:
1. Apply power while holding down .
OFF
ON
^
V
Hold down during power up
2. When the unit is on, release . The display will
indicate if the current offset is keel offset or
waterline offset:
Hull Offset (Depth below the keel)
Surface Offset (Depth below the surface)
3. After 5 seconds the display will indicate the
current offset.
Note: A negative offset is used to display depth
below the keel and a positive offset is used to
display depth below the surface.
8. To exit this mode, press and hold both
and
2 Instrument Setup
4. Use and to change the value. If either key
is held depressed for more than one second the
reading will increase or decrease rapidly.
5. The offset can be programmed in 0.1 unit steps
from -9.9 to 9.9 feet (or equivalent). When
programmed for a negative offset, ‘-’ will be
indicated on the left hand side of the display.
6. To display depth below the keel enter the
vertical distance between the bottom of the keel
and the depth transducer as a negative value.
7. To display depth below surface enter the
vertical distance from the waterline to the
depth transducer as a positive number (no
negative sign).
Hold down
during power up
simultaneously. Alternatively, if no keys are
pressed for a period of 5 seconds normal depth
display will resume.
OFFON
^
V
Press simultaneously
The display will now indicate the current water
depth.
Transducer Setting
A Transducer Setting is provided to allow the Depth
2100 to be used with different transducer types. The
default setting (= 0.0) is used for most transducers.
Some transducers ‘ring’ after the sonar transmit pulse
(just like hitting a bell). This ringing can be interpreted
as an echo from a shallow bottom. The setting is
used to increase the required level that shallow
echoes must meet before they will be displayed.
If the Depth 2100 gives repeated false readings of
1.5 to 3 feet depth while in deep water the transducer
setting should be increased. Adjust it upward by 0.5
at a time and retest. The range of values is -0.9 to
+2.5. If the value is set too high it could cause erratic
readings in shallow water.
Changing the Transducer Setting:
1. Apply power while holding down
. The
display will show either HOF or SOF for 7
seconds. Continue to hold the key down.
2. The display will show tdr.
tdr
3. Release the key.
4. After 2 seconds the display will show the
Transducer Setting value eg 0.0.
5. Use and to change the value.
6. To exit this mode, press and hold both
and
simultaneously.
Units of Measure
To select the displayed unit
1. Apply power while holding down
.
OFF
V
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Navman Depth 2100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Navman Depth 2100 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Navman Depth 2100

Navman Depth 2100 User Manual - German - 10 pages

Navman Depth 2100 User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info