30268

Multiplex ROYALevo7 Manual

54
Zoom out
Zoom in
Previous page
1/77
Next page
ROYAL evo 7 - Instructions
Page 53
ENGLIS
H
19. Setting up a new model
19.1. Introduction
When you set up a new model the ROYALevo7 helps
you by presenting a set of model templates. Eight dif-
ferent templates are available:
Templates for
standard and
fixed-wing models
Templates for
model
helicopters
1. BASIC1 7. HELImech
2. BASIC2 8. HELIccpm
3. ACRO
4. DELTA
5. GLIDER
6. 4 FLAPS
Setting up a new model based on a model template is
very simple, as all parameters and menus not required
for the selected model type are suppressed. This en-
sures that the menu system is always as clear and sim-
ple as possible, and goes a long way to avoiding pro-
gramming errors.
A detailed description of model templates and their ap-
plications, together with full information and set-up fa-
cilities, are found on the section starting with Î 20.
“Step by step to your destination”
There are various ways of proceeding when you are set-
ting up a new model. The following procedures for
fixed-wing models (Î 19.2.) and helicopters (Î 19.3.)
describe the method which in our opinion takes you to
the finishing post most quickly.
19.2. A new (fixed-wing) model
Step n Setting up a new memory
A new model is initially set up in Menu I Memory, in the
New Model sub-menu (Î 18.6.).
In this menu the following happens:
1. The first empty memory is automatically selected
for the new model.
(
Memory No. parameter Î 18.6.1.)
2. Select a model template to suit the new model.
(
Template parameter Î 18.6.2.)
From the eight templates available pick the one
which comes closest to your model.
(Description of model templates Î 20.)
3. Select the manufacturer-specific servo sequence at
the receiver (from MULTIPLEX HiTEC, Futaba or JR)
(
Servo config parameter Î 18.6.3.)
4. Select your preferred stick mode, i.e. which stick is
to control which model function (e.g. throttle right
or left, aileron right or left, …)
(
Mode parameter Î 18.6.4.)
5. Leave the menu by selecting
OK
this completes setting up the new model.
6. In the Control sub-menu of the Setup menu, select
the control neutral settings for:
Thr. min Idle
Spoiler min retracted
(no braking effect)
(Î 13.3.3. und 13.3.4.)
Step
o Entering a model name
Enter the model’s name in the menu:
I
Memory / Properties.
(
Name parameter Î 18.5.6.)
Step
p Connecting the servos
Connect the model’s servos, speed controller etc. to the
receiver, taking care to use the socket sequence de-
scribed in the model template which you selected when
you initially set up the new model (
Servo config.
parameter). The channel sequence can also be seen in
Menu K
Servo / Assignment.
TIP:
Not all receiver channel assignments are fixed; some
channels can be altered, i.e. they are unused and can be
assigned freely. For example, you can assign a throttle
or aero-tow channel if necessary for a glider or electric-
powered glider. You can assign additional functions to
the servo channels which are not in use by basic func-
tions (e.g. retracts, second elevator servo, aero-tow, va-
cant AUX channels, …). Changes to the servo assign-
ment can be made in Menu K
Servo / Assign-
ment
( Î 16.2.).
Note:
If you wish to connect devices (servos, speed controller,
…) which vary in signal format, it is possible to set up
each channel separately (options: UNI / MPX) in Menu K
Servo / Assignment
( Î 16.2.).
Step
q Switching on the transmitter and receiver
! Always keep to the standard sequence!
Always switch the transmitter on first,
and only then the receiver.
! Caution!
Injury hazard from motors bursting into life.
Check carefully that there is no danger of a motor
starting up accidentally when you switch on.
The model will now respond to control commands from
the transmitter. However, all the settings (servo direc-
tion, neutral setting, control surface travels) still have to
be checked and adjusted.
Step
r Calibrating the servos
The term “calibration” in this connection means adjust-
ing the following features of the servos:
- Direction of rotation
- Centre setting
- End-points
The servos are calibrated in Menu K
Servo, Cali-
brate
( Î 16.1.)
Note:
Please take great care when calibrating the servos. They
can only work accurately enough to provide precise
control of your model if this process is carried out prop-
erly and carefully. “Measuring is always better than
guessing!”
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo7 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo7

Multiplex ROYALevo7 User Manual - German - 77 pages

Multiplex ROYALevo7 User Manual - Dutch - 110 pages

Multiplex ROYALevo7 User Manual - French - 77 pages

Multiplex ROYALevo7 User Manual - Italian - 75 pages

Multiplex ROYALevo7 User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info