30268

Multiplex ROYALevo7 Manual

55
Zoom out
Zoom in
Previous page
1/77
Next page
ROYAL evo 7
Page 54
Step s Setting up mixers
Mixers are set up in Menu G Mixer. This menu is dy-
namic, i.e. only those mixers used in the model are dis-
played. Mixer types and their function are described in
detail in the section on model templates (Î20.).
By default the mixers are assigned sensible average set-
tings for the model template in use, but they still have
to be fine-tuned to suit your particular model.
Details on the subject “setting up mixers” can be found
in the Mixer section (Î 15.4.).
Step
t Setting up the transmitter controls
Transmitter controls are set up in Menu H Control.
This menu is dynamic, i.e. only the controls required for
your model / model template are displayed. By default
the control settings are assigned sensible values for the
model template you have selected, but they still need to
be fine-tuned to suit your particular model.
All you need to know on the subject “Setting up trans-
mitter controls” can be found in the Section Î 14.
Step
u Pre-flight checks
Your newly set-up model should now be ready to fly.
But be sure to check all the working systems carefully
before you attempt to fly it.
Fine-tuning, especially of mixers and transmitter control
settings, can only be carried out during the test-flying
procedure with the new model. Please don’t try to make
changes in a menu while the model is flying. It is far
safer and more convenient to use the 3D digi-adjustors
to alter the values (Î 10.2.2.).
Step
v Activating flight phases
If you have set up a model based on one of the model
templates
BASIC2 ... 4 FLAPS, you can optimise the
model’s settings for various flight tasks by switching to
other flight phases. Before activating additional flight
phases the model should first be test-flown and
trimmed out properly in one flight phase (generally the
NORMAL phase), and all mixer and transmitter control
settings finalised. Only then should you activate addi-
tional flight phases as required, in order to optimise the
model for different flight situations, such as landing /
aerobatics, thermal / speed, cruise / auto-rotation. An-
other flight phase has first to be released, and then the
settings can be copied from the first flight phase to the
new one. The transmitter control settings (Menu H
Control
Î 14.) can now be optimised for the new
flight phase. All transmitter control settings which are
marked with a small number (
1 …3 or 4) can be ad-
justed separately for each flight phase.
You will find all you need to know about flight phases in
the Section Î 18.4.
19.3. A new model helicopter
! Safety note
Radio-controlled model helicopters are technically so-
phisticated and demanding flying machines which re-
quire careful setting-up, maintenance and care. If oper-
ated incompetently or carelessly they represent a seri-
ous potential hazard.
If you are a beginner, this is our advice:
x Start by asking an experienced model pilot for help;
join a club, or enrol at a model flying training centre;
x Ask your local model shop for advice;
x Read all you can on the subject (books, magazines).
Step
n Setting up a new memory
A new model is initially set up in Menu I Memory, in the
New Model sub-menu (Î 18.6.).
In this menu the following happens:
1. The first empty memory is automatically selected
for the new model.
(
Memory No. parameter Î 18.6.1.)
2. Select one of the two helicopter model templates
(
Template parameter Î 18.6.2.)
HELImech
For models with mechanical rotor
head mixing
HELIccpm
For models with electronic rotor head
mixing (CCPM). The type of swash-
plate (e.g. 3-point 120q, 3-point 90q,
...) is irrelevant. The settings for your
particular swashplate type will be en-
tered later.
A detailed description of the helicopter model
templates can be found at Î 20.
3. Select the manufacturer-specific servo sequence at
the receiver (from MULTIPLEX, HiTEC, Futaba or JR)
(
Servo config. parameter Î 18.6.3.)
4. Select your preferred stick mode, i.e. which stick is
to control which model function (e.g. collective
pitch right or left, roll right or left, …)
(
Mode parameter Î 18.6.4.)
5. Leave the menu by selecting
OK
this completes setting up the new model.
6. In the Control sub-menu of the Setup menu, select
the control neutral settings for:
Coll. min Control setting for negative
collective pitch
Thr.limit min Idle setting
(Î 13.3.3. and 13.3.4.)
Step
o Entering a model name
Enter the model’s name in the menu:
I
Memory / Properties.
(
Name parameter Î 18.5.6.)
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo7 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo7

Multiplex ROYALevo7 User Manual - German - 77 pages

Multiplex ROYALevo7 User Manual - Dutch - 110 pages

Multiplex ROYALevo7 User Manual - French - 77 pages

Multiplex ROYALevo7 User Manual - Italian - 75 pages

Multiplex ROYALevo7 User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info