30268
48
Zoom out
Zoom in
Previous page
1/77
Next page
ROYAL evo 7 - Instructions
Page 47
ENGLIS
H
16.2.2. Free assignment with model helicopters
If you have set up a model helicopter based on one of
the model templates HELImech or HELIccpm, various
transmitter controls can be selected for the free or vari-
able channels. You can find out which channels are free
or variable by consulting the descriptions of the heli-
copter model templates (Î 20. onward):
Available
controls
Note
Pitch-ax
Pitch-axis signal only no mixing
Yaw
Yaw signal only no mixing
Throttle
Throttle signal, plus mixed throttle curve,
throttle limiter, direct throttle, EMERGENCY
throttle CUT
Spoiler
Spoiler signal only no mixing
RPM
Control signal for speed controller
L. gear
Retract signal no mixing
Aero-tow
Aero-tow signal mixing
Brake
Brake signal mixing
Gyro
Gyro signal, including all mixed signals
from the
Gyro mixer
Mixture
Mixture signal only no mixing
AUX1
AUX2
AUX1/2 signal only no mixing
Coll. P.
Coll. pitch signal only no mixing
16.2.3. Special features when assigning
The transmission mode PPM 6 or PPM 7 is set automati-
cally:
Last servo on channel 6 PPM 6
Last servo on channel 7 PPM 7
Problems may occur with PPM 6 and certain older types
of speed controller, in which case it may help to assign
any function to channel 7. This forces PPM 7 operation;
you do not need to connect a servo to the output.
16.3. Sub-menu: Monitor
The Servo Monitor is a substitute for a receiving system
and servos, enabling you to check the function and op-
eration of servos, speed controllers and - especially -
gyro systems (for which an external effect is not easy to
detect), and seek and eliminate faults.
Call up the menu, then press the ENTER button or a 3D
digi-adjustor; the Servo Monitor then appears.
Two display variants are available:
x graphic, with bar-form display of output signals
(Fig. 1), and
x numerical, with display of % values (Fig. 2).
You can switch between the two displays using the UP /
DOWN buttons ( / ) or one of the two 3D digi-
adjustors.
Press the ENTER button or one of the 3D digi-adjustors
to close the Servo Monitor.
16.4. Sub-menu: Test run
Automatic servo run, designed for test and demonstra-
tion purposes or as an “electronic aid” for range-
checking.
As soon as you select a transmitter control, the transmit-
ter generates a constant control signal with variable
transit time, i.e. from one end-point of the control to the
other. All servos which are operated by this transmitter
control, either directly or via a mixer, start running.
You can interrupt the test run by either of two methods:
x Press the REV/CLR button “ Control
“ appears
x Select no transmitter control (“ - - - - - - - “)
The transit time can be set to any value in the range 0.1
– 4.0 seconds.
17.Main Menu Timer A
The ROYALevo7 features a stopwatch with alarm func-
tion which can be used for various timing tasks. The
stopwatch counts up to 4½ hours with a resolution of
one second.
Line 1:
Time
This is the time which has elapsed since the timer
started. If you select this field, you can erase the time
using the REV/CLR button.
The stopwatch can also be reset by pressing the
REV/CLR button when you are in one of the status dis-
plays 1 - 3.
Line 2:
Alarm
This is where you set the alarm time. For example, if the
motor run of an electric-powered model is four minutes,
you should set
0:04:00 at this point. The timer adds
together the motor run time based on the throttle set-
ting, and emits a warning sound once the set alarm time
has elapsed.
The method of entering the alarm time differs from the
usual procedure: here the value is entered digit by digit:
press the ENTER button or one of the 3D digi-adjustors.
The cursor jumps to the hours, which can then be set
using the UP / DOWN buttons or one of the 3D digi-
adjustors. Every time you press ENTER again, the cursor
moves one place to the right etc.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Multiplex ROYALevo7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Multiplex ROYALevo7 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Multiplex ROYALevo7

Multiplex ROYALevo7 User Manual - German - 77 pages

Multiplex ROYALevo7 User Manual - Dutch - 110 pages

Multiplex ROYALevo7 User Manual - French - 77 pages

Multiplex ROYALevo7 User Manual - Italian - 75 pages

Multiplex ROYALevo7 User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info