672423
8
Zoom out
Zoom in
Previous page
1/15
Next page
Operating manual English
5
Before switching on the engine,
carry the unit at least 10 m away
from the filling station. While filling
the tank or using the unit, do not
smoke and keep sparks and
naked flames out of the area.
Replace damaged exhausts, fuel
tanks, or filler caps.
Operating the unit
Never start the unit and never
leave it running in a closed room
or building. The inhalation of
exhaust gases may be fatal.
Use the unit outdoors only.
Wear eye and ear protection when
using the unit. If working in a dusty
environment, wear a face or dust
mask. A long-sleeved shirt is
recommended.
Wear thick, long trousers , boots
and gloves. Do not wear loose
clothing, jewellery, short trousers,
sandals and do not walk barefoot.
Pin your hair above your shoulders.
If required, wear a hair net.
The cutting attachment cover must
always be attached when you use
the unit as a lawn trimmer. Both
trim lines must be pulled out and
the correct line must be installed.
The trim line must not be pulled
out over the end of the cover.
The unit has a clutch. The cutting
attachment stops when the unit is
running at no load. If it does not
stop, have the unit adjusted by
a mechanic at your authorised
dealer.
Before switching on the unit,
ensure that the line spool/cutting
blade cannot strike an object.
Adjust the handle bar to your
height so that the you have
the unit under control.
Operate the unit in daylight or
adequate artificial lighting only.
Avoid starting the unit
unintentionally. Be ready to operate
the unit when you pull the starter
rope. User and unit must be in
a stable position when the unit
is started. Follow the Start/Stop
instructions.
Use this unit for its designated
purpose only.
Do not stretch too far over the unit.
Always have a secure footing and
keep your balance.
When operating the unit, always
hold the unit firmly with both hands.
Always hold both sides of the
handle bar firmly.
When operating the unit, always
wear the shoulder belt.
Do not use the unit in adverse
weather conditions, e.g. if there is
a probability of rain or a storm.
Never change the engine settings
preset at the factory.
Keep away from naked flames,
avoid creating sparks and do not
smoke.
Never operate the unit with
a defective ignition switch.
Keep your hands, face and feet
away from all moving parts. Do
not touch the cutting attachment
while it is rotating and do not
attempt to stop it.
Do not touch the engine or muffler.
These parts become very hot
while the unit is being used. They
remain hot for a short time even
when the unit is switched off.
Do not let the engine run quicker
than required for cutting or
trimming of lawn edges. Do not
run the engine at high speed when
it is not cutting.
Always switch off the engine if you
cannot start cutting immediately
or if you are moving from one
place to another.
If unusual vibrations occur, switch
off the engine immediately. Check
the unit for damage. If the unit is
damaged, contact a specialist
company.
If you strike or ensnare a foreign
object, immediately switch off the
engine and check whether the unit
has been damaged. Never use the
unit with loose or damaged parts.
Before removing blockages or
performing other work on the unit,
switch off the engine and remove
the spark-plug terminal.
Stop and switch the engine off
before performing maintenance or
repairs or before changing cutting
attachments. Also pull out the
spark-plug terminal.
Use only original spare parts
for repairs. These parts can be
purchased from your authorised
dealer.
Never use parts, accessories or
attachments which are not
authorised for this unit. Otherwise,
the user may be seriously injured
and the unit damaged. In addition,
your warranty may be deemed
null and void.
Keep the unit clean and ensure
that there are no plants or other
objects caught between the cutting
attachment and guard.
To reduce the risk of fire, please
replace damaged mufflers and
spark extinguishers and remove
grass, leaves, excess lubricants
and layers of soot from the engine
and muffler.
Have all repairs carried out by
a repair shop only.
Working with the cutting
blade (depending on model)
Before operating the unit, please
read all safety instructions carefully.
Always keep the handle bar
between the user and cutting
attachment.
NEVER cut material if the cutting
blade is 75 cm or higher above
ground level.
The unit may recoil if the rotating
blade strikes an object which
cannot be cut immediately.
Recoils may be strong enough to
throw the unit and/or user in any
direction and may cause the user
to lose control of the unit. Recoils
may occur without warning if the
blade gets caught, jams or locks.
This can easily happen in areas in
which the material to be cut is
difficult to see.
Never use the undergrowth blade
to cut undergrowth thicker than
12.7 mm. Otherwise, violent
recoils may occur.
When using the cutting blade,
the cutting attachment cover
must always be attached.
Do not attempt to touch or stop
the blade while it is rotating.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD 1033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD 1033 in the language / languages: English as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD 1033

MTD 1033 User Manual - German - 16 pages

MTD 1033 User Manual - Dutch - 16 pages

MTD 1033 User Manual - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info