672423
10
Zoom out
Zoom in
Previous page
1/15
Next page
Operating manual English
7
Operating and display
elements
`~ìíáçåK=
a~ã~ÖÉ=íç=íÜÉ=~ééäá~åÅÉ
qÜáë=Ñáêëí=ÇÉëÅêáÄÉë=íÜÉ=Åçåíêçä=~åÇ=
Çáëéä~ó=ÑìåÅíáçåëK=aç=åçí=ÉñÉÅìíÉ=
~åó=çÑ=íÜÉëÉ=ÑìåÅíáçåë=óÉí>
Fig. 1
1 Exhaust cover
2 Spark plug
3Starter handle
4 Tank cap
5 Intake pump/primer
6Choke lever
7 Air filter cover
8 Handle bar
9 Shaft
10 Cutting attachment cover
11 Line cutting blade
12 Line coil
13 Gearbox
14 Holder for cutting
attachment cover
15 Holder for cable harness
16 Throttle
17 Ignition switch
18 Throttle lock
19 Shoulder belt holder
20 Cutting blade with cutting
attachment cover *
21 Retaining bar *
22 Socket wrench *
* depending on model
Installation manual
a~åÖÉê
oáëâ=çÑ=áåàìêó=Ñêçã=ÉåÖáåÉ=ÄÉáåÖ=
ëí~êíÉÇ=ìåáåíÉåíáçå~ääóK
mêçíÉÅí=óçìêëÉäÑ=Ñêçã=áåàìêóK=
_ÉÑçêÉ ïçêâáåÖ=çå=íÜÉ=ÉåÖáåÉW
Ó pïáíÅÜ=çÑÑ=íÜÉ=ÉåÖáåÉI
Ó t~áí=ìåíáä=~ää=ãçîáåÖ=é~êíë=Ü~îÉ=
ÅçãÉ=íç=ëí~åÇëíáääX=íÜÉ=ÉåÖáåÉ=
ãìëí=Ü~îÉ=ÅççäÉÇ=ÇçïåK
Ó oÉãçîÉ=ëé~êâJéäìÖ=íÉêãáå~äK
Disposal instructions
Dispose of packaging remnants,
old units, etc., in accordance with
local regulations.
Installing and setting the
handle bar
Fig. 2
Insert the handle bar (1) into the
lower holder (2).
Hook the upper retaining plate (3)
into the openings (4) of the lower
holder and secure with the toggle
screw (5).
Hold the unit in the operating
position (Fig. 13) and position the
handle bar until you have a secure
footing.
Tighten the toggle screw (5) firmly
until the handle bar (1) is secure.
Press the cable harness (6) into
the holder (7).
Adjusting the carrying
system (shoulder strap)
Fig. 3
1. Place harness over your
shoulders.
2.
Close the catch on the chest belt.
If required, readjust.
3.
Close the catch on the abdominal
belt. If required, readjust.
4. Adjust the shoulder, abdominal
and chest belts to the correct
length/width.
5. Latch the hook of the carrying
system into the holder on the unit
and adjust the attachment pad to
a comfortable length.
Attaching the cutting
attachment cover
Fig. 4
Attach cutting attachment cover (1)
to the holder (2) using the two
screws (3).
Tighten screws firmly.
Attaching/removing
the line head
Attaching the line head
Fig. 5
If attached, remove cutters and
blade attachment parts before-
hand. See “Removing the cutting
blade”.
Push spacer (1) onto the
drive shaft (2).
Align the 3 openings in the
spacer (3), the gearbox (4) and
the gear cover (5).
Note
If alignment is not correct, the line
head cannot be attached/removed!
Insert retaining bar (6) through the
openings (3, 4, 5) in order to secure
the gearbox.
While holding the retaining bar (6),
turn the line head (7) anti-clockwise
(to the left) onto the drive shaft.
Tighten line head firmly!
Note
Ensure that the line head (7) is
seated correctly on the spacer (1),
i.e. centred and resting flat!
Remove retaining bar from the
gear head.
Remove the line head
Fig. 6
Align the openings (3, 4, 5). Insert
retaining bar (6) through the
openings and hold in position.
Unscrew line head (7) clockwise
(to the right) off the drive shaft.
Attaching/removing the
cutting blade (depending
on model)
Attaching the cutting blade
Fig. 7
If attached, remove the line head
beforehand. See “Attaching/
removing the line head”.
Note
When attaching the cutting blade
for the first time, remove the blade
attachment parts (blade holder (8),
retaining bell (9), nut (10)) if attached.
See “Removing the cutting blade”.
Push spacer (1) onto the
drive shaft (2).
Align the 3 openings in the spacer
(3), the gearbox (4) and the gear
cover (5) (Fig. 5).
Note
If alignment is not correct, the cutting
blade cannot be attached/removed!
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MTD 1033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MTD 1033 in the language / languages: English as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MTD 1033

MTD 1033 User Manual - German - 16 pages

MTD 1033 User Manual - Dutch - 16 pages

MTD 1033 User Manual - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info