779576

Motorola ML25254 Manual

22
Zoom out
Zoom in
Previous page
1/36
Next page
22
8.6 Switching Between the Speakerphone, Handset and Headset Mode
1. To switch to the speakerphone mode, press s. The speakerphone indicator illuminates. Place
the corded handset back into the cradle.
2. To switch to the corded handset, pick up the handset. The speakerphone or wired headset
indicator will turn o.
3. To switch to the headset, press HEADSET to enable the headset, and the headset indicator
illuminates.
8.7 Mute
To have a private, o-line conversation, use the Mute feature. The party on the other end of the
line cannot hear you, but you can still hear them.
1. During a call, press MUTE to activate the Mute feature.
2. Press MUTE again to de-activate.
NOTE
The Mute LED indicator will illuminate when the Mute feature is activated.
8.8 Do Not Disturb (DND)
This feature will disable your telephone’s ringer for a set period of time to prevent incoming calls
from interrupting. When an incoming call or intercom call occurs, the status indicators will light up
but the phone will not ring.
1. In idle mode, press DND/PRIVACY. The last setting is displayed.
2. Using VOL + and VOL - of the navigation button to scroll to your selection. You can choose
from as short as
15 MINUTES, 30 MINUTES, 45 MINUTES, 1 HOUR
or
2 HOURS
and increase the
duration by 1-hour intervals up to
24 HOURS
.
3. Press
SELECT
softkey to save your selection. The indicator on the base will blink and a DND
timer will appear on the display indicating how much time remains before the DND feature is
automatically turned o.
4. To turn o DND feature at any time, press DND/PRIVACY.
8.9 Line Privacy
This feature will prevent other phones on the same system from accessing the line used by your
active call.
To turn on Line Privacy:
1. While on a call, press DND/PRIVACY.
2. The screen will display
PRIVACY
.
8.10 Flash
If you subscribe to Call Waiting Caller ID service from your local telephone company and you
receive an incoming call during a call, you will hear a beep to indicate another call is waiting on the
line and Caller ID information (if available) for the waiting call shows on the display.
1. To connect to the waiting call, press FLASH and your first call will be put on hold.
2. To switch between the two calls, press FLASH.
8.11 Inserting a Pause in the Dialing Sequence
Press j twice to insert a delay in dialing sequence when a pause is needed to wait for a dial
tone (for example, after you dial 9 for an outside line, or to wait for a computer access tone). Each
pause counts as one digit in the dialing sequence, and is shown as
P
in the display.
8.12 Redial
1. Pick up the handset, press s or HEADSET and the base will select the first available line. If
both lines are available, Line 1 will be used first.
Or, press LINE 1 or LINE 2 button to select the line you want.
2. Press REDIAL. The redial number list (last 3 previously dialed numbers) is shown.
3. Using VOL + and VOL - of the navigation button to scroll to the number you want to redial.
4. Press
DIAL
softkey to dial the phone number.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Motorola ML25254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Motorola ML25254 in the language / languages: English as an attachment in your email.

The manual is 2.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info