633940
26
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
26
Every time the machine is switched
off
Check whether the saw blade overrun
exceeds 10 seconds; if the overrun is
longer than this, have the motor re-
placed by a qualified electrician.
Monthly (if used daily)
Remove saw dust and chips with vacu-
um or brush; apply light coat of oil to
guide elements:
threaded rod and guide rods of
blade rise and fall mechanism:
–swivel segments.
Every 150 hours of operation
Check all screwed joints, retighten if
necessary.
If necessary:
Set table leg guide bushings.
Turn Allen screws (73a) clockwise =
guide sluggish.
Turn Allen screws (73a) counter-
clockwise = guide moves easily.
Further fine adjustment by means of
a setscrew (73b).
Setting guide bushings on front leg
mount:
Turn Allen screws (74) clockwise =
guide sluggish.
Turn Allen screws (74) counter-
clockwise = guide moves easily.
Setting guide bushings on rear leg
mount:
Turn Allen screws (75) clockwise =
guide sluggish.
Turn Allen screws (75) counter-
clockwise = guide moves easily.
Tighten all Allen screws diagonally
and evenly.
Before cutting a workpiece to size
make trial cuts on pieces of scrap.
Always place a workpiece on the saw
table in such way that it cannot tilt or
rock (e.g. always place a curved
board on the table with the convex
side up).
To simplify repetitive cut-off work
use a stock stop.
Keep surface of table clean.
Use only genuine Metabo accessories.
Use only accessories that fulfil the re-
quirements and specifications listed in
these operating instructions.
For a complete range of accessories,
see www.metabo.com or the catalogue.
Danger!
For safety reasons, repairs to power
tools must be carried out by quali-
fied electricians only using original
spare parts!
If you have Metabo electrical tools that
require repairs, please contact your Me-
tabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
Power tools do not belong in
the household rubbish.
According to European Di-
rective 2002/96/EC on waste
electrical and electronic
equipment, used electrical devices must
be collected separately and taken to an
environmentally friendly recycling ?facil-
ity.
Contact your local council for informa-
tion on disposal of the used tool.
All packaging materials are recyclable.
Danger!
Before carrying out any fault service
or maintenance work, always:
1. switch machine off.
2. unplug mains cable.
3. wait for saw blade to come to
standstill.
Check that all safety devices are op-
erational again after each fault ser-
vice.
Motor does not run
The restart protection is active. If the
mains plug is inserted with the machine
switched on, or if the current supply is
restored following an interruption, the
machine does not start up:
Switch the machine off and on
again.
No mains voltage
Check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
Remove cause for overheating, let
cool off for a few minutes. Then re-
start machine.
Speed is not reached
Overload protection: There is a MAJOR
reduction in load speed.
The motor temperature is too high!
Allow the machine to run at idle
speed until it has cooled down.
Overload protection: There is a SLIGHT
reduction in load speed.
73a
73b
74
9. Tips and Tricks
10. Available Accessories
11. Repairs
75
12. Disposal
13. Troubleshooting
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS 254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS 254 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info