633940
24
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
24
5. Cut workpiece by pushing the mitre
fence forward.
6. Switch machine off if no further cut-
ting is to be done immediately after-
wards.
Danger!
Before every transport:
switch machine off.
wait for saw blade to come to
standstill.
unplug mains cable.
Lower saw blade fully.
Set saw blade bevel angle to 0° and
lock with lock lever.
Remove add-on parts (blade guard,
dust extraction). Store blade guard
at saw table.
Wind up mains cable on cable reel.
Only tools with machine stand:
Raise tool on frame and swing to the
rear. Set up machine on its edge
and fold in upper legs. The red turn-
ing levers must engage again.
Swing machine to the rear and fold
in the lower legs. The red turning le-
vers must engage again.
Push in handles and set down ma-
chine.
Crushing hazard
Lock pulled-out table side extension
with lock lever.
Use handles (63) provided on sides of
table to carry the machine.
Caution!
Do not carry the machine at the
guards, table side extension or oper-
ating elements!
Mobile transport:
Pull out handle, turn it and engage it.
Pull or push saw with handle
If possible use original carton for ship-
ping.
Danger!
Prior to all servicing:
1. switch machine off.
2. wait until the saw has come to a
complete stop.
3. unplug mains cable.
Check that all safety devices are op-
erational again after each service.
Replace defective parts, especially
safety devices, only with genuine re-
placement parts. Parts not tested
and approved by the equipment
manufacturer can cause unforeseen
damage.
Repair and maintenance work other
than described in this section should
only be carried out by qualified spe-
cialists.
Danger!
With a damaged table insert there is
a risk of small parts getting stuck
between table insert and saw blade,
blocking the saw blade. Replace
damaged table inserts immediately!
8.1 Saw blade change
Danger!
Directly after cutting the saw blade
can be very hot – burning hazard!
Let a hot saw blade cool down. Do
not clean the saw blade with com-
bustible liquids.
Risk of injury, even with the blade at
standstill. Wear gloves when chang-
ing blades.
When fitting a saw blade, observe
the direction of rotation!
1. Raise saw blade fully.
2. Remove blade guard.
3. Loosen table insert (64) and remove
from table.
4. Turn clamping nut (68) with open-
jawed spanner and , at the same
time, pull lever for saw blade lock
(65) upwards until it engages.
5. Hold lever firmly in position and un-
screw clamping nut clockwise.
6. Remove clamping nut (68), outer
blade flange (67) and saw blade
from saw spindle.
7. Clean clamping surfaces of saw
blade flange (66) and (67) and saw
blade.
7. Transport
63
8. Care And Maintenance
64
65
66
67
68
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS 254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS 254 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info