633940

Metabo TS 254 Manual

25
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
25
Danger!
Do not use cleaning agents (e.g. to
remove resin residue) that could
corrode the light metal components
of the saw; the stability of the saw
would be adversely affected.
8. Push inner saw blade flange (66)
onto motor shaft.
9. Put on a new saw blade (observe di-
rection of rotation!).
Danger!
Use only saw blades conforming to
the technical specifications stated
and to EN 847-1 – if unsuitable, dam-
aged or deformed saw blades parts
are used, parts can be ejected due
to centrifugal force in an explosive-
type manner.
Do not use:
– saw blades which permissible
maximum speed is below the rat-
ed no-load speed of the saw
spindle (see “Technical Specifi-
cations”);
– saw blades made of high speed
steel (HS or HSS);
– saw blades whose cutting width
is less than, or whose blade body
is thicker than, the thickness of
the riving knife.
– saw blades with visible damage;
– cut-off wheel blades.
Danger!
– Mount saw blade using only gen-
uine parts.
– Do not use loose-fitting reducing
rings; the saw blade could work
loose.
– Saw blades have to be mounted
in such way that they do not
wobble or run out of balance and
cannot work loose during opera-
tion.
10. Slide on outer blade flange (67).
11. Screw on clamping nut (68) (left-
handed thread!). Turn clamping nut
(68) with open-jawed spanner and,
at the same time, pull the lever of the
saw blade lock (65) upwards until is
engages.
12. Hold lever firmly in position and
tighten clamping nut hand-tight by
turning counterclockwise.
Danger!
– Do not extend arbor bolt tighten-
ing wrench.
– Do not tighten arbor bolt by hit-
ting the wrench.
13. Adjust riving knife corresponding to
the saw blade size (69).
(for riving knife setting, see 5.1)
14. Reinstall table insert.
15. Attach blade guard.
8.2 Adjusting the blade tilt
stop
1. Set the blade tilt stop lever (71) for
the angle range to 0° / 45°.
2. Lock set bevel tilt by tightening lock
lever (70).
3. Check blade bevel angle:
– 0° = at right angles to the saw ta-
ble
– 45° with separate mitre square.
If these angles are not achieved ex-
actly:
4. Release cross-head screw (72) at
respective cam disc and adjust cam
plate until the blade bevel angle in
relation to the saw table is exactly 0°
(= right angles), or 45°, in the end
positions.
5. Retighten cross-head screw at cam
plate.
6. After adjusting the stop limitation, re-
adjust angle scale at front side if
necessary.
Note:
To set the bevel angle limitation of -1.5°
to 46.5°, the blade tilt stop lever must be
pulled out.
8.3 Saw storage
Danger!
Store the machine beyond the reach
of children. Store the machine such
that it cannot be put into operation
by unauthorised personnel and such
that the stationary machine cannot
cause injury.
Caution!
Do not store saw unprotected out-
doors or in damp environment.
8.4 Maintenance
Saw Cleaning
Remove chips and saw dust with
vacuum cleaner or brush:
– from saw blade setting guide ele-
ments;
– from motor vent slots;
–chip case.
–Height adjustment
– Swivel guide
Before switching ON
Visual check to see if
– distance between saw blade and riv-
ing knife is 3 to 5 mm.
– riving knife is in line with saw blade.
Visual check of power cable and power
cable plug for damage; if necessary
have damaged parts replaced by a
qualified electrician.
69
70
71
72
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS 254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS 254 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info