595156
30
Zoom out
Zoom in
Previous page
1/76
Next page
30
C
C: To set dial gauge to zero, loosen knob and lower
motor until the router bit rests on the workpiece.
Then retighten knob.
C: Pour régler le point zéro, desserrer le pommeau et
ramener la partie moteur vers le bas jusqu’à ce que
la défonceuse s’appuie sur la pièce à usiner.
Puis, resserrer fortement le pommeau.
C: Zur Einstellung des Nullpunktes Knaufgriff lösen und
den Motorteil nach unten führen bis der Fräser auf
dem Werkstück aufsitzt.
Anschließend Knaufgriff wieder festziehen.
C: Om het nulpunt in te stellen knopgreep losmaken en
het motorgedeelte naar beneden geleiden tot de
frees op het werkstuk stuit.
Daarna knopgreep weer vastdraaien.
C: Per impostare il punto zero, allentare il pomello e
abbassare il blocco motore fino a fare aderire la fresa
al pezzo in lavorazione.
Ristringere il pomello.
C: Para el ajuste del punto cero, aflojar la empuñadura
de bola y dirigir la parte del motor hacia abajo hasta
que la fresa apoye sobre la pieza a mecanizar.
Seguidamente, apretar de nuevo a fondo la
empuñadura de bola.
C: Para colocar o medidor em zero, desapertar o punho
e deslocar a parte com o motor para baixo até a
tupia assentar na peça a fresar.
Em seguida, voltar a apertar o punho.
C: För nollpunktens inställning lossa knoppen och för
motordelen nedåt tills fräsen vilar på arbetsstycket.
Sedan dras knoppen fast igen.
C: Nollapisteen säätöön irrota nuppikahva ja siirrä
moottoriosa alas kunnes jyrsin tarttuu
työkappaleeseen.
Kiinnitä nuppikahva.
C: For innstilling av nullpunktet løsnes
innstillingsknappen og motordelen føres nedover,
inntil fresen hviler på arbeidsstykket.
Deretter trekkes innstillingsknappen til igjen.
C: Til indstilling af nulpunktet løsnes indstillingsknappen
og motordelen føres nedad, indtil fræseren hviler på
arbejdsstykket.
Derefter strammes indstillingsknappen igen.
C:W celu nastawienia punktu zerowego należy zwolnić
gałkę uchwytu i przesunąć część silnikową frezarki w
dół, aż frez zetknie się z przedmiotem obrabianym.
Należy wówczas ponownie dokręcić gałkę uchwytu
C:A nullpont beállításához oldja a fogantyúgombot és a
motorrészt vezesse lefelé, amíg a maró a
munkadarabra fel nem fekszik.
Majd a fogantyúgombot ismét húzza meg.
C:Για τη ρύθµιση του µηδενικού σηµείου
χαλαρώστε τη σφαιρική λαβή και κατεβάστε το
µέροσ του κινητήρα έωσ του καθίσει η φρέζα
πάνω στο τεµάχιο προσ επεξεργασία.
Κατπιν σφίξτε πάλι τη σφαιρική λαβή.
OfE_1229_Signal_0112_Teil1.qxp:OfE_1229_Signal_0508_Teil1.qxp 27.02.2013 16:57 Uhr Se
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo OF E 1229 SIGNAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo OF E 1229 SIGNAL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info