595156
28
Zoom out
Zoom in
Previous page
1/76
Next page
28
Setting depth of cut (A-H)
Clean, accurate cuts are achieved at a maximum milling depth of 6 mm. This also protects the motor
from over-load.
To achieve a greater depth of cut, repeat process.
Réglage de la profondeur de fraisage (A-H)
On obtient un fraisage propre et sûr avec une profondeur de fraisage maximale de 6 mm. Par la même
occasion, le moteur est ainsi protégé contre toute surcharge.
Des profondeurs de fraisage plus importantes peuvent être obtenues en passant plusieurs fois sur la
pièce.
Frästiefe einstellen (A–H)
Sauberes und sicheres Fräsen erreicht man bei einer maximalen Frästiefe von 6 mm.
So wird auch der Motor vor Überlastung geschützt.
Größere Frästiefen können durch mehrere Durchgänge erzielt werden
Freesdiepte instellen (A-H)
Een nauwkeurig en veilig freesresultaat bereikt men bij een maximale freesdiepte van 6 mm. Zo wordt
ook de motor tegen overbelasting beveiligd.
Grotere freesdiepten kunnen worden bereikt door meerdere freesdoorgangen
Regolazione della profondità di fresatura (A-H)
Per una fresatura pulita e sicura si consiglia di lavorare con una profondità massima di 6 mm. In questo
modo si evita un sovraccarico del motore.
E' però possibile ottenere maggiori profondità di fresatura passando più volte.
Ajuste de la profundidad de fresado (A-H)
Con una profundidad máxima de 6 mm se obtiene un fresado fiable
y limpio al mismo tiempo que se evita la sobrecarga del motor.
Para obtener un fresado más profundo, repetir el proceso las veces necesarias.
Regular a profundidade de fresar (A-H)
Só é possível fazer fresagens exactas e seguras até uma profundidade máxima de 6 mm.
Assim o motor é ao mesmo tempo protegido contra sobrecargas.
Fresagens mais profundas obtêm-se através de várias passagens.
Inställning av fräsdjup (A-H)
Ordentlig och säker fräsning åstadkommer man med ett maximalt fräsdjup på 6 mm.
Så skyddas även motorn för överbelastning.
Större fräsdjup kan uppnås genom flera omgånger.
Jyrsinsyvyyden säätö (A-H)
Siisti ja varma jyrsintä saadaan aikaan kun jyrsinsyvyys on korkeintaan 6 mm.
Näin suojataan myös moottori ylikuormitukselta.
Suuremmat jyrsinsyvyydet saadaan aikaan jyrsimällä useita kertoja.
Innstilling av fresedybde (A-H)
Ren og sikker fresing oppnås ved en maksimal fresedybde på 6 mm.
Slik beskyttes også motoren mot overbelastning.
Større fresedybder kan oppnås ved hjelp av flere arbeidsganger.
Indstilling af fræsedybden (A-H)
Ren og sikker fræsning opnås ved en maksimal fræsedybde på 6 mm.
Således beskyttes motoren samtidig mod overbelastning.
Større fræsedybder kan opnås ved hjælp af flere arbejdsgange.
Nastawienie głębokości frezowania (A-H)
Dokładne i niezawodne wyniki frezowania uzyskane zostają przy wykorzystaniu maksymalnej
głębokości frezowania wynoszącej 6 mm.
Przy tej głębokości frezowania silnik jest chroniony przed przeciążeniem.
Większe głębokości frezowania można uzyskać w kilku przejściach roboczych.
Marásmélység beállítása (A-H)
Pontos és biztos marás maximálisan 6 mm marásmélység mellett érhető el.
Ezáltal a motor is védve van a túlterheléstől.
Nagyobb marásmélység több fogás révén érhető el.
Ρύθµιση βάθουσ φρεζαρίσµατοσ (Α-Η)
Καθαρ και ασφαλέσ φρεζάρισµα είναι δυνατ σε µέγιστο βάθοσ φρεζαρίσµατοσ 6 mm.
Έτσι προστατεύεται και ο κινητήρασ απ υπερφρτιση.
Βαθύτερο φρεζάρισµα µπορεί να γίνει µε επανάληψη φρεζαρίσµατοσ.
OfE_1229_Signal_0112_Teil1.qxp:OfE_1229_Signal_0508_Teil1.qxp 27.02.2013 16:57 Uhr Se
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo OF E 1229 SIGNAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo OF E 1229 SIGNAL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info